Product
Article
NameDescriptionContent
ABB Bailey INFI 90 system IMASI03 Analog Input Slave Module
ABB Bailey INFI 90 system IMASI03 Analog Input Slave Module
Universal Analog Input Slave Module IMASI03
The Universal Analog Input Slave Module (IMASI03) interfaces
field inputs to the multi-function processor module. The
IMASI03 supplies 16 separate process field signals into the
INFI 90® Process Management System. These analog inputs are
used by the Multi-Function Processor Module (MFP) to monitor
and control a process.
Universal analog input slave modules provide an isolated thermocouple,
millivolt, RTD, and high level analog signal interface
for the Multi-Function Processor Module with variable analog-
to-digital conversion resolution up to a maximum of 24
bits.
This instruction explains the slave module features, specifications
and operation. It details the procedures to set up and
install an IMASI03 module, and explains status indicators that
help in system test and diagnosis.
System engineers or technicians using the IMASI03 should
read and understand this instruction before installing and
operating the slave module. In addition, a complete understanding
of the INFI 90 system is beneficial to the user
The Universal Analog Input Slave Module (IMASI03) performs
analog input signal processing for up to 16 input channels and
sends this information to a Multi-Function Processor
(IMMFP01/02/03) in the INFI 90® System.
This manual explains the purpose, operation, maintenance,
handling precautions and installation procedures of the slave
module.
System engineers and technicians should read this manual
before installing the IMASI03 module. Put the module into
operation only after reading and understanding the information
in this manual. Refer to the Table of Contents to find specific
information. Refer to the HOW TO USE THIS MANUAL
entry in this section to get started.
The IMASI03 is a single printed circuit board that occupies one
slot in an INFI 90 Module Mounting Unit (MMU). Two captive
latches on the module faceplate secure it to the MMU. The
slave module has three card edge connectors for external signals
and power: P1, P2 and P3. P1 connects to the supply voltages.
P2 connects the IMASI03 to the slave expander bus, over
which it communicates with the MFP.
Connector P3 carries the inputs from the input cable plugged
into the termination unit (TU) or termination modules (TM).
The terminal blocks for field wiring are on the TU/TM.
The single dipswitch on the IMASI03 module sets the address
for the slave or selects on-board tests. Refer to Section 3 for the
steps to set the module address. Refer to Section 6 for the
on-board tests. Be sure to check the switch setting before putting
the module into the MMU.
Jumpers configure the type of analog input signals. Refer to
Section 3 for the correct setting of these jumpers.
Figure 1-1 shows the INFI 90 communication levels.
The design of the IMASI03 module, as with all INFI 90 modules,
allows for flexibility in creating a process management
system. Refer to the NOMENCLATURE entry of this section to
see the list of devices that can be used with the slave module in
an INFI 90 system.
• The IMASI03 conditions (filters, amplifies and isolates) up
to 16 analog input signals.
• The IMASI03 converts analog signals to digital values, adds
compensation and corrections as needed, and provides digital
values to the MFP through the slave expander bus.
Each channel is individually programmable for these input
types:
E, J, K, L, N (14 AWG), N (28 AWG), R, S, T, U thermocouples.
Chinese type E and Chinese type S thermocouples.
Millivolt (-100 to +100 mV).
3-wire RTDs (10, 100 U.S., 100 European, 120 and Chinese
53 Ohm).
High level (-10 to +10 V).
Current (4-20 mA).
• Resolution of the analog-to-digital conversion process is
programmable over a range from 16 to 24 bits.
• Input type and channel resolution may be selected independently
for each channel, permitting any mix of inputs
on a single IMASI03 module.
• Channel isolation and open input detection are provided
for each channel.
• Input circuit offset, gain and nonlinearity errors are
recorded during a one time factory calibration procedure.
These measurements provide error compensation during
normal operation. The slave does automatic recalibration
during normal operation to compensate for component
aging and temperature drift. No user calibration is ever
required.
• Engineering units conversion to degrees C or F is automatically
calculated on all input signals that are thermocouple
or RTD types. These conversions correct for nonlinearities
in the conversion to temperature units using industry
standard linearization tables.
• The slave scales the block output value to engineering
units for low and high level voltage inputs. Input type and
zero and span values are specified in function code 216.
• Thermocouple inputs have cold junction compensation.
Each termination device has a built-in cold junction reference.
The cold junction reference applied to thermocouple
inputs may be this built-in reference or it may be a remote
reference read from another input from this or another
slave.
• The slave compensates for lead wire resistance in the connection
between the thermocouple, RTD or low level voltage
input signals.
• The IMASI03 can be removed or installed without turning
off power to the system.
IMASI02
IMASI03
IMASI13
IMASI23
IMASM03
IMASO01
IMASO11
IMBLK01
IMCIS02
IMCIS12
IMCIS22
IMCOM03
IMCOM04
IMCPM02
IMDSI02
IMDSI12
IMDSI13
IMDSI22
IMDSM04
IMDrSM05
IMDSO01
IMDSO02
IMDSO04
IMDSO14
IMDSO15
IMFAI01
IMFBS01
IMFCS01
IMFEC11
IMFEC12
IMHSS02
IMMFC04
IMMFC05
IMMFP01
IMMFP02
IMMFP03
IMMFP03B
IMMFP11
IMMFP12
IMMPI01
IMPCC01
IMRIO02
IMSDO01
IMSET01
INBIM02
INBTM01
INICT01
The Universal Analog Input Slave Module (IMASI03) interfaces
field inputs to the multi-function processor module. The
IMASI03 supplies 16 separate process field signals into the
INFI 90® Process Management System. These analog inputs are
used by the Multi-Function Processor Module (MFP) to monitor
and control a process.
Universal analog input slave modules provide an isolated thermocouple,
millivolt, RTD, and high level analog signal interface
for the Multi-Function Processor Module with variable analog-
to-digital conversion resolution up to a maximum of 24
bits.
This instruction explains the slave module features, specifications
and operation. It details the procedures to set up and
install an IMASI03 module, and explains status indicators that
help in system test and diagnosis.
System engineers or technicians using the IMASI03 should
read and understand this instruction before installing and
operating the slave module. In addition, a complete understanding
of the INFI 90 system is beneficial to the user
The Universal Analog Input Slave Module (IMASI03) performs
analog input signal processing for up to 16 input channels and
sends this information to a Multi-Function Processor
(IMMFP01/02/03) in the INFI 90® System.
This manual explains the purpose, operation, maintenance,
handling precautions and installation procedures of the slave
module.
System engineers and technicians should read this manual
before installing the IMASI03 module. Put the module into
operation only after reading and understanding the information
in this manual. Refer to the Table of Contents to find specific
information. Refer to the HOW TO USE THIS MANUAL
entry in this section to get started.
The IMASI03 is a single printed circuit board that occupies one
slot in an INFI 90 Module Mounting Unit (MMU). Two captive
latches on the module faceplate secure it to the MMU. The
slave module has three card edge connectors for external signals
and power: P1, P2 and P3. P1 connects to the supply voltages.
P2 connects the IMASI03 to the slave expander bus, over
which it communicates with the MFP.
Connector P3 carries the inputs from the input cable plugged
into the termination unit (TU) or termination modules (TM).
The terminal blocks for field wiring are on the TU/TM.
The single dipswitch on the IMASI03 module sets the address
for the slave or selects on-board tests. Refer to Section 3 for the
steps to set the module address. Refer to Section 6 for the
on-board tests. Be sure to check the switch setting before putting
the module into the MMU.
Jumpers configure the type of analog input signals. Refer to
Section 3 for the correct setting of these jumpers.
Figure 1-1 shows the INFI 90 communication levels.
The design of the IMASI03 module, as with all INFI 90 modules,
allows for flexibility in creating a process management
system. Refer to the NOMENCLATURE entry of this section to
see the list of devices that can be used with the slave module in
an INFI 90 system.
• The IMASI03 conditions (filters, amplifies and isolates) up
to 16 analog input signals.
• The IMASI03 converts analog signals to digital values, adds
compensation and corrections as needed, and provides digital
values to the MFP through the slave expander bus.
Each channel is individually programmable for these input
types:
E, J, K, L, N (14 AWG), N (28 AWG), R, S, T, U thermocouples.
Chinese type E and Chinese type S thermocouples.
Millivolt (-100 to +100 mV).
3-wire RTDs (10, 100 U.S., 100 European, 120 and Chinese
53 Ohm).
High level (-10 to +10 V).
Current (4-20 mA).
• Resolution of the analog-to-digital conversion process is
programmable over a range from 16 to 24 bits.
• Input type and channel resolution may be selected independently
for each channel, permitting any mix of inputs
on a single IMASI03 module.
• Channel isolation and open input detection are provided
for each channel.
• Input circuit offset, gain and nonlinearity errors are
recorded during a one time factory calibration procedure.
These measurements provide error compensation during
normal operation. The slave does automatic recalibration
during normal operation to compensate for component
aging and temperature drift. No user calibration is ever
required.
• Engineering units conversion to degrees C or F is automatically
calculated on all input signals that are thermocouple
or RTD types. These conversions correct for nonlinearities
in the conversion to temperature units using industry
standard linearization tables.
• The slave scales the block output value to engineering
units for low and high level voltage inputs. Input type and
zero and span values are specified in function code 216.
• Thermocouple inputs have cold junction compensation.
Each termination device has a built-in cold junction reference.
The cold junction reference applied to thermocouple
inputs may be this built-in reference or it may be a remote
reference read from another input from this or another
slave.
• The slave compensates for lead wire resistance in the connection
between the thermocouple, RTD or low level voltage
input signals.
• The IMASI03 can be removed or installed without turning
off power to the system.
IMASI02
IMASI03
IMASI13
IMASI23
IMASM03
IMASO01
IMASO11
IMBLK01
IMCIS02
IMCIS12
IMCIS22
IMCOM03
IMCOM04
IMCPM02
IMDSI02
IMDSI12
IMDSI13
IMDSI22
IMDSM04
IMDrSM05
IMDSO01
IMDSO02
IMDSO04
IMDSO14
IMDSO15
IMFAI01
IMFBS01
IMFCS01
IMFEC11
IMFEC12
IMHSS02
IMMFC04
IMMFC05
IMMFP01
IMMFP02
IMMFP03
IMMFP03B
IMMFP11
IMMFP12
IMMPI01
IMPCC01
IMRIO02
IMSDO01
IMSET01
INBIM02
INBTM01
INICT01
-
Schneider GUTOR OC0935 Power Factor Sampling Board
-
Schneider GUTOR OC0922 Analog Signal Isolation Board
-
Schneider GUTOR OC0908 Battery Voltage Detection Board
-
Schneider GUTOR OC0947 Temperature / IGBT Sampling Board
-
Schneider GUTOR OP2601 Communication Expansion Board
-
Schneider Electric GUTOR OP2312 bypass control board
-
Schneider Electric GUTOR OP2130 Cooling Fan Monitoring & Control Board
-
Schneider Electric GUTOR OP2010 Battery Test Board / Battery Management Diagnostic Card
-
Schneider Electric GUTOR OP2552 Three-phase Power Connection Board Assembly
-
Schneider Electric GUTOR OP1922A Parallel Control Board / Load-Sharing Synchronization Module
-
Schneider Electric GUTOR OP6290B Inverter Feedback Acquisition Board / Signal Scaling Module
-
Schneider GUTOR OP6280 Basic Signal Board
-
Schneider Electric GUTOR OP2456 / OP2456B Main control board
-
Schneider Electric GUTOR OP2452 Power Plug-in Panel
-
Schneider Electric GUTOR OP2450 Parallel Communication Board
-
Schneider Electric GUTOR OP2406 Interface Fuse Monitoring Board
-
Schneider Electric GUTOR OC0919 High-Power Semiconductor Module
-
Schneider Electric GUTOR OP6281A System Logic Interface Board
-
Schneider Electric GUTOR OP6285A Power Signal Acquisition Board
-
Schneider Electric GUTOR OP2438 Fan Monitor & Drive Protection Board
-
Schneider Electric GUTOR OP2446 Main Control CPU Board
-
ROLLS-ROYCE CE05-00 Steering Gear Control Module
-
ROLLS-ROYCE MARINE AS-BRATTVAAG WRC1021A CONTROLLER CARD
-
ROLLS ROYCE DECK MACHINERY MPC-300-A7029099 TERMINAL CONTROLLER UNIT
-
ROLLS-ROYCE HELICON THRUSTER CONTROL PANEL LF90S-01-06
-
Rolls-Royce PCC1030C Panel Controller Card
-
Rolls-Royce RRDIO15 Remote Digital Input/Output Module
-
Rolls-Royce TDI-11 Pitch & Direction Indicator Module
-
Rolls-Royce CCN 01 CANman Controller Network Module
-
Rolls-Royce SLIO 01 CANman Controller Network Module
-
Rolls-Royce MPC-210 Winch & Propulsion Control Module
-
Rolls-Royce MTI-144 Engine Control Module
-
Rolls-Royce Tenfjord FB10-002 Steering Gear Module (E-4500-40-1)
-
ROLLS ROYCE MARINE AS CIRCUIT BOARD (PCB) RRAI016
-
Rolls-Royce Marine AS PIP6-1 Marine Controller
-
ROLLS-ROYCE MPC-300 STARTER CONTROL UNIT A7029099
-
Rolls-Royce Data Respons MPCF1-10.4" Maritime Panel Computer
-
ROLLS-ROYCE MARINE OLC-40009 PCB CARD
-
Rolls-Royce Marine Brattvaag WRC1021B Controller Board
-
ROLLS-ROYCE CCN 01 & ROLLS-ROYCE SLIO 02 CANMAN CONTROLLER NETWORK
-
ROLLS-ROYCE ATC-3-A7033172 AQUAMASTER TURNING CONTROLLER
-
ROLLS-ROYCE POSCON V.3 JOYSTICK MODULE 6459
-
Rolls-Royce Marine 389-496-00 Joystick Remote Control Panel 6799-W, 389-996-00
-
Rolls-Royce data respons 10.4'' Panel Computer 98H010A0000I/R10I53S
-
Rolls-Royce H1127.0101 Marine Controller 000068308
-
Rolls-Royce CU40-0106-50 Steering Gear Control Panel
-
Beckhoff Polaris CP7011-1002-0010 operator operator HMI display 30.5 cm
-
Beckhoff AM8052-0JH1-0000 Servomotor 10.7 Nm (M0), F5 (104 mm)
-
Beckhoff AM8052-0JH1-0000 Servomotor 10.7 Nm (M0), F5 (104 mm)
-
Beckhoff BX5100-0000 CANopen Bus Terminal Controller
-
Beckhoff CX9020-0115 PLC Module CX90200115
-
Beckhoff module EJ7211-0010 EtherCAT plug-in module
-
BECKHOFF AX5203-0000 Servo Driver
-
BECKHOFF CP6201-0001-0020 24VDC UNMP
-
Beckhoff CX5120-0135 Embedded PC CPU Module
-
BECKHOFF C5240-0020/000224115 Plc Module
-
Beckhoff CP2918-0000 PanelCP29xx-0000 | Multi-touch built-in Control Panel with DVI/USB Extended interface
-
Beckhoff CX2020-0122 Embedded PC Controller
-
Beckhoff C6640-0040 Control Cabinet Industrial PC 7-Slot
-
BECKHOFF CONTROL CABINET INDUSTRIAL PC - C6930-1062-0050
-
Beckhoff Automation EtherCAT Terminal EK1100 EK1122
-
Beckhoff CP6533-0001-0060 IPC
-
Beckhoff EK9500 | EtherNet/IP™ Bus Coupler
-
Beckhoff CP6202-1047-0050 - An industrial-grade embedded panel computer.
-
Beckhoff C6650-0040 Industrial PC
-
BECKHOFF CX5230-0185 / 000119805 PLC Module
-
Beckhoff EL3773 PLC Module
-
BECKHOFF EL4732 (PKG OF 10) NSMP
-
Beckhoff CP6202-0001-0010 Economy Built-In Panel
-
Beckhoff AX5206-0000-0202 Digital Compact Servo Drives 2-channel
-
Beckhoff Panel PC CP6606-0001-0020 7-inch Economy Panel PC
-
Beckhoff CPU basic module CX2020-0155 + power supply module CX2100-0004
-
Beckhoff CP2913-000 Multi-Touch Display
-
Beckhoff CP6500-1012-0060 14250369 Control Cabinet
-
Beckhoff CP7902-0001-0000 Economy Control Panel with DVI/USB Extended interface
-
Beckhoff C6920-0010 Core Duo 2.00 GHz
-
BECKHOFF C3640-0050 Build-in Industrial PCs
-
Beckhoff KL6023-0000 KL6023 EnOcean Wireless-Adapter
-
Kollmorgen AKM54G-ANC2DB00 servo motor
-
Kollmorgen S200 Series S20350-VTS SERVO DRIVE
-
KOLLMORGEN AKD-P00606-NBCC-I000 SERVO DRIVE
-
Kollmorgen MV65WKS-CE310/22PB Servo Drive Control Module
-
Kollmorgen S20360-VTS-021 Servo Drive
-
KOLLMORGEN CR06550 High-precision digital servo amplifier
-
KOLLMORGEN DBL5N01050-03S-VV0-S40 Phase AC Synchronous Brushless Servo Motor
-
KOLLMORGEN S70301-NANANA-024 SERVO DRIVE
-
Kollmorgen S20360-VTS S200 Series Servo Drive
-
Kollmorgen RBE-03011-A00 Brushless Frameless Servo Motor
-
KOLLMORGEN AKD-T00306-NBAN-0000 INPUT SERVO DRIVE
-
KOLLMORGEN S700 Servo Controller S70302-NANANA
-
Kollmorgen AKD-P00607-NBEC-0000 400/480VAC 4.40KVA Servo Drive.
-
KOLLMORGEN S70102-NANANA SERVO DRIVE
-
KOLLMORGEN AKM21E-ANSNEH02 PM Servo Motor & PRD-AMPE25EB-00 Servo Drive Array
-
KollMorgen SC1R06260 Servo Drive 1.4/2.2 KVA 115230 Vac
-
Kollmorgen AKD-P00306-NBAN-0000 Servo Drive
-
Kollmorgen TTB2-2042-3052-A DC Motor Industrial Drive 5.5A 185 oz/inIntegrated safety
-
KOLLMORGEN SERVOSTAR 610-AS SERVO AMPLIFIER_SERVOSTAR610AS_S61001
-
KOLLMORGEN Seidel 60WKS-CE240/26PB 26A Servo Drive Module Control 60WKS-M240/26
-
KOLLMORGEN PRD-0016400P-10 & PRD-0016600D-30 Axis Control System Modules
-
KOLLMORGEN Seidel DBL5N01700-03S-000-S40 Servo Motor
-
HIRSCHMANN RS30-0802O6O6SDAP RAIL SWITCH
-
Hirschmann RS20-1600M2T1SDAEHH03.1.02 Rail Switch
-
Hirschmann RSPM20-4T14T1EV9HHS999.9.99 Managed Ethernet Switch
-
Hirschmann BELDEN RS40-0009CCCCSDAPHH09.0.14 / RS400009CCCCSDAPHH09014
-
Hirschmann RS40 Rail Switch RS40-0009CCCCSDAE
-
Hirschmann BELDEN RS30-0802T1T1SDAP / RS300802T1T1SDAP Fully Managed Layer 2 Compact Rail Switch
-
Hirschmann BELDEN RS20-0800M2M2SDAUHH / RS200800M2M2SDAUHH
-
Hirschmann EAGLE30-04022O6TT999SCCY9HSE3F Industrial Firewall Router Switch
-
Hirschmann RS20-1600T1T1SDAEHH09.0.14 RS20 Rail Mount Ethernet Switch
-
Hirschmann EAGLE 0200T1T1TDDY90000HHE05.3.03 Industrial Security Router
-
Hirschmann - BELDEN MIPP-AD-1L9P
-
HIRSCHMANN RSPM20-4Z64Z6TV9HHS9 942 106-999 RAIL SAFETY SWITCH
-
HIRSCHMANN FIBEROPTIC MODULE FIP P/N: OZDFIPG3 T
-
HIRSCHMANN RS20-1600M2M2SDAUHH Ethernet rack-mounted switch
-
BELDEN RS20-0400T1T1SDAEHH04.0.01 / RS200400T1T1SDAEHH04001
-
HIRSCHMANN MM2-4FXM3 MICE Media Module
-
Hirschmann RS20-2400T1T1SDAP / RS20-2400T1T1SDAPHH05.0.02
-
GE MLJ1005B010H00C MLJ Digital Synchromism Check
-
ALSTOM MICROTECH DX21-M2 Digital Excitation Controller
-
HIRSCHMANN BRS20-1200ZZZZ-STCY99HHSES
-
HIRSCHMANN MM3-4FXM2 MICE Media Module
-
Hirschmann RSB20-0800T1T1SAABHH 8Port ENet Rail Switch RSB20
-
Hirschmann MACH102-8TP Ethernet Switch
-
SAACKE DDZ-M marine steam pressure atomizer
-
SAACKE SKV-A marine rotary cup atomizer
-
SAACKE Seavis HMI05e
-
Kollmorgen MMC-SD-2.0-230 Servo Drive 100-240VAC 2KW 10A Output 3PH 100-240VAC
-
Kollmorgen Servo drive CR10550
Kong-Y
Product
WhatsApp
Add: High-tech Software Park, Xiamen City, Fujian Province
Mobile: +86-17750019513(WhatsApp)
Email: yy4291644@gmail.com
Website: https://www.abb-sis.com
Contact us
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
Tell：
-
Schneider GUTOR OC0935 Power Factor Sampling Board
-
Schneider GUTOR OC0922 Analog Signal Isolation Board
-
Schneider GUTOR OC0908 Battery Voltage Detection Board
-
Schneider GUTOR OC0947 Temperature / IGBT Sampling Board
-
Schneider GUTOR OP2601 Communication Expansion Board
WeChat
Copyright © 2009 - 2025 Cld , All Rights Reserved KONG-Y
+86-17750019513
Factory case show