FOXBORO FCP280 FCP270 FEM100 P0926HZ P0923LR P0926JM P0926KH P0926JF

FOXBORO FCP280 FCP270 FEM100 P0926HZ P0923LR  P0926JM P0926KH P0926JF
The I/A Series® system DIN rail mounted subsystem allows you to distribute process input/output modules
to strategic points within your plant.

FEATURES
Key features for the DIN rail mounted subsystem are:
 Allows you to locate control processor and field
input/output modules in strategic plant areas
 High performance Fieldbus Modules (FBMs)
 Enclosures to provide various levels of
environmental protection
 Optional redundant power
 Variety of modular mounting configurations
 High performance, high accuracy, fast updates
 Optional Intrinsically Safe baseplates for FBMs
 Reduced component count, for ultra-high
reliability and quality
 Optional redundancy
 Harsh (Class G3 - ISA S71.04) contamination
protection
 Distributed local and/or remote I/O
 Power security and alarming
 Electrical isolation and field device power
 High-speed system communication.
OVERVIEW
The I/A Series system DIN rail mounted subsystem
innovative equipment packaging, together with the
integrated use of Fast Ethernet networks with fiber
optic cable for communication between equipment
domains, permits local or remote distribution of your
process I/O points.
The DIN rail mounted subsystem consists of a full line
of high performance Fieldbus Modules (FBMs), along
with the following integrally designed elements:
 Field Control Processor 280 (FCP280) and Field
Control Processor 270 (FCP270) – Similar in size
to the FBMs, this compact control processor
provides a control interface between the FBMs
and the control network and allows you to locate
the control processor in strategic plant areas.
 Z-Module Control Processor 270 (ZCP270) – In
the Z-module form factor for use with 100 Series
FBM racks, this compact control processor
provides control operations for the FBMs and
allows you to locate the control processor in
strategic plant areas.
 Fieldbus Communications Modules (FCMs) –
Similar in size to the FBMs, these compact
modules provide a communication interface
between the FBMs and the ZCP270 via The
Mesh control network.
 FBI200 Fieldbus Isolator/Filter - Similar in size to
the FBMs, these compact, optional modules,
among other functions, extend the 268 kbps
Module Fieldbus between FCP280s/FCP270s
and 100 Series FBMs up to 1830 m (6000 ft)
over twinaxial cable.
 Modular Baseplates – These provide a
communications backplane and a solid base for
mounting the FBMs, FCMs, or FCP280s allowing
for a variety of remote equipment mounting
configurations.
 Intrinsically Safe Baseplates (ISTA-BPs) –
Compatible with standard modular baseplates,
the ISTA-BPs were co-developed with Pepperl
and Fuchs and provide an Intrinsic Safe solution
for I/A Series 200 Series FBM applications.
 Enclosures – Several basic types provide various
levels of environmental protection and equipment
grouping for the DIN rail mounted equipment.
The DIN rail mounted FBMs provide full support for
analog measurement, digital sensing, and analog or
discrete control capabilities. The FBMs are rugged,
high performance distributed process I/O modules
designed for all process control tasks. Operating in
conjunction with the I/A Series control processor
(FCP280, FCP270, or ZCP270), these FBMs provide
for process management and control of continuous,
batch and discrete control schemes.
HIGH PERFORMANCE, HIGH ACCURACY,
FAST UPDATES
The DIN rail mounted FBMs offer high resolution,
high accuracy, and repeatable design. The Sigma-
Delta, fast integrating converter used on the analog
inputs provides new readings as fast as every 25 ms,
suitable for high-speed regulatory control
applications. The analog inputs use a built-in
configurable moving average filter that efficiently
removes process noise and power line frequencies.
REDUCED COMPONENT COUNT FOR ULTRAHIGH
RELIABILITY AND QUALITY
All logic functions (I/O process, I/O specific logic,
communication processor, and other interconnecting
logic functions) are integrated into a
single Application Specific Integrated Circuit (ASIC).
The use of ASIC:
 Reduces the number of components in the
module
 Reduces the size of the module
 Reduces the heat generated by the module
 Reduces the cost of the module
 Produces a module having ultra-high reliability
and quality.
A single module has an expected availability above
0.999974. [This assumes that the module resides in
a baseplate with redundant power, and a mean time
to repair (MTTR) of two hours.]
An optionally redundant module has an expected
availability above 0.9999964. (This assumes that the
module resides in a baseplate with redundant power,
and a MTTR of two hours.) The redundancy of the
module pair, coupled with the high coverage of faults,
provides a very high subsystem availability time.
OPTIONAL REDUNDANCY
The DIN rail mounted subsystem is optionally
available with total redundancy, for high reliability and
availability. Redundancy is available for; the power
supplies, The Mesh control network, the FCMs, the
FEMs(1)), the FCP280, Modular Fieldbus cables
between baseplates and certain FBM I/O module
types.
RUGGED, INNOVATIVE PACKAGING
The DIN rail mounted Fieldbus Modules are
packaged as structurally identical plug-in modular
assemblies. To permit mounting in harsh
environments, each module has a rugged, extruded
aluminum exterior, without open vent holes, for
physical protection of the circuits. Heat generated
within the module is conducted from the module via
the aluminum finned cover. This approach to
protection prevents contaminants in the plant
environment from reaching the control components,
greatly extending the life of the equipment. The
operating temperature for a module is rated at either
50°C, 60°C, or 70°C depending on the module and
termination assembly type. The specific Product
Specification Sheet (see “Fieldbus Modules” on
page 14) for each module lists the specific operating
temperature for the module.
The standard DIN rail mounted subsystem has the
following product safety certifications:
 Underwriters Laboratories (UL) listing for both US
(NRTL) and Canadian (UL-C) requirements for
both ordinary and hazardous locations
 CENELEC (DEMKO) certification for use in
potentially explosive atmospheres
 CE approved.
For additional information about certifications, refer to
PSS 31H-2W2 B3.
Light-emitting diodes (LEDs) incorporated into the
front of each module provide visual status indications
of the Fieldbus Module functions.
The small size of these FBMs allows ample room in
an enclosure to terminate field wiring near the FBM.
MODULAR BASEPLATE MODULE MOUNTING
The DIN rail mounted Fieldbus Modules mount on
specially designed Modular Baseplates (Figure 1,
only vertical baseplates shown). The Modular
Baseplates fasten to a structurally supported non
isolated DIN rail for mounting inside or outside an
enclosure. (As an alternative to DIN rail mounting, a
mounting plate can be used for horizontal mounting
of the Modular Baseplate on a 19-inch rack). The
Modular Baseplate provides increased overall system
installation functionality by providing unit increments
of 2, 4 and 8 module positions with various
operational functionality in combination with vertical
and horizontal mounting. The Modular Baseplates
can thus be mounted in small, distributed cabinets or
in a variety of other mounting configurations.
The Modular Baseplates are backwards compatible
with existing DIN I/O subsystems allowing for future
expansion without additional interface hardware and
includes the following:
 Primary and secondary 24 V dc power
connections
Two Module Fieldbus connections (for A/B
Module Fieldbus daisy chain)
 Power/communication connection and field I/O
connection for each FBM
 DIP switch for baseplate identification
 A/B Module Fieldbus and optional time strobe
splitter/terminator connection
 Adding additional baseplates without removing
the system from service (requires redundant
Module Fieldbus).
Any FBM (except FBM232/233) can be removed
from the Modular Baseplate without removing or
disturbing external field device wire terminations or
internal cable terminations or connections.
FCPs, and FCMs require removal of wiring to the
control network.
Shielded twisted-pair cables for Modular Baseplate
interconnections are available in various lengths of
0.25 m (10 in) up to 60 m (198 ft). The maximum
twisted-pair cable length interconnecting all
baseplates is 60 m (198 ft).
Figure 1 shows selected vertical DIN rail mounted
Modular Baseplates. Horizontal DIN rail mounted
Modular Baseplates are available in similar styles as
the vertical mounted baseplates, but equivalents for
each style are not all available. Refer to
PSS 21H-2W6 B4 for additional information on the
remaining DIN rail mounted Modular Baseplates.

Please contact us (kongjiang automation technology), consultation purchase!

 P0912CE NODEBUS B EXTENSION CABLE
 P0913ED DISK DRIVE
 P0914SV INPUT MODULE FBM203 ANALOG ISOLATED 8POINT RTD
 P0914SY I/O MODULE FBM204 4POINT 0-20 IN 4POINT 0-20 OUT
 P0914TD INPUT MODULE FBM207 120AC/125DC,240AC EXCITATION
 P0914TN INPUT MODULE FBM211 DIFFERENTIAL 16POINT 0-20MA
 P0914TN-fbm211 FBM211 DIFFERENTIAL 16 INPUT 0-20 MA
 P0914TR INPUT MODULE FBM217 15-60VDC 120VAC/115VDC 240VAC
 P0914WH INPUT MODULE FBM207B CH ISOLATED 16 DIN 24 VDC
 P0914XA BASEPLATE HORIZONTAL 200SERIES DINRAIL MT FIELDBUS
 P0914XB BACKPLANE 8 SLOT REDUNDANT POWER
 P0914XG I/O MODULE FBM205 4PT 0-20MA IN / 4PT 0-20MA OUT
 P0914YM COMMUNICATION MODULE FCM10E ENET TRUNK TO FIELDBUS
 P0914YM-FCM10E FCM10E FIELDBUS COMMUNICATION MODULE
 P0914ZM IDENTIFICATION MODULE FCMID
 P0915FU TRACKBALL SUN SERIES 51
 P0916AE TERMINATION ASSEMBLY FBM203 3TIER 3WIRE RTD
 P0916AG TERMINAL ASSEMBLY COMPRESSION FBM204
 P0916AG-FBM204 COMPRESSION TERM ASSY, FBM204
 P0916AJ TERMINATION ASSEMBLY FBM205 3TIER COMPRESSION
 P0916AM TERMINATION ASSEMBLY FBM207 2TIER COMPRESSION
 P0916BT TERMINATION ASSEMBLY FBM211 2TIER COMPRESSION
 P0916CP COMMUNICATION MODULE FCM10EF 2KM FIELDBUS
 P0916DD CABLE 5 METERS FBM2XX TYPE 1 TERM
 P0916DE CABLE ASSEMBLY TYPE1 10METER 8POINT 37SUB-25DSUB
 P0916DF CABLE ASSEMBLY TYPE1 15METER 8POINT 37DSUB-25DSUB
 P0916FK CABLE 5 METERS FBM2XX TYPE 4 TERM
 P0916FL CABLE ASSEMBLY TYPE4 10METER 16POINT 37DSUB-37DSUB
 P0916FM CABLE ASSEMBLY TYPE4 15METER 16POINT 37DSUB-37DSUB
 P0916GV CABLE ASSEMBLY P0940HW TO P0940XA OR P0940XB 84IN
 P0916GX CABLE ASSEMBLY P0940HW TO P0940XA OR P0940XB 30IN
 P0916GY CABLE ASSEMBLY P0940HW TO P0940XA OR P0940XB 48IN
 P0916GZ CABLE ASSEMBLY P0940HW TO P0940XA OR P0940XB 60IN
 P0916JT TERMINAL ASSEMBLY COMPRESSION FBM211 EXT POWERED
 P0916JT-FBM211 COMP TERM ASSY, FBM211, EXT POWERED
 P0916JW I/O MODULE FBM241C CSENSE IN + 2A 60V FUSED OUT
 P0916JZ TERMINATION ASSEMBLY FBM242 FUSED 2TIER COMPRESSIO
 P0916MZ CABLE 2MBPS MODULE TO P0940XA OR P0940XB 1METER
 P0916NG TERMINATION ASSEMBLY FBM242 2TIER COMPRESSION
 P0916NN REDUNDANT ADAPTOR
 P0916PY TERMINATION ASSEMBLY FBM217 2TIER COMPRESSION
 P0916RB TERMINATOR BASEPLATE
 P0916TA OUTPUT MODULE FBM242 16POINT 2AMP 60VDC RELAY
 P0940BW PROCESSOR MICRO I/A 4SLOT
 P0940DH POWER SUPPLY MICRO I/A 24V
 P0940FT POWER SUPPLY MICRO I/A GE 6.5VDC
 P0950BM TRANSMITTER INTERFACE DUAL BAUD INTELLIGENT
 P0950BM-FBM43 DUAL BAUD INTELLIGENT TRANSMITTER INTERFACE
 P0950CB RACK
 P0960AH MODULE FAULT TOLERANT Z CONNECTOR
 P0960AW PROCESSOR MODULE 30
 P0960GC WORKSTATION PROCESSOR WP30
 P0960GX TRANSFORMER ISOLATION VIDEO
 P0961BC CONTROL PROCESSOR CP40B
 P0961FR CONTROL PROCESSOR CP60
 P0970BC INTERFACE MODULE DUAL NODEBUS
 P0970BC-DNBI DUAL NODEBUS INTERFACE MODULE