DS215KLDCG1AZZ03B Power connection board

Part Number DS215KLDCG1AZZ03B Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS215KLDCG1AZZ03B is a Power Connect Board developed by GE. It is a part of Mark V Series. The board includes specific firmware that supports its operation and ensures compatibility with other system components. Firmware updates may be necessary to maintain optimal performance. Connectors and Interfaces: Equipped with various connectors, facilitates easy connections to other boards and components within the control system. Keypad Removal Procedure Preliminary Steps: If replacing a C revision board, skip directly to board removal. Remove Bezel and Components: Remove the screws securing the bezel, then take off the bezel, gasket, and overlays. Remove Keypad Screws: Unscrew the ten inner screws holding the keypad. Avoid removing the outer screws to prevent the unit from falling out of the enclosure. Carefully pry up the keypad from the top. Disconnect Connections: Lift the keypad and disconnect the lKPL, 2KPL, and 3KPL connectors from the display board. Keypad Installation Procedure Reinstall Keypad: Reverse the removal steps, but do not reconnect the lKPL, 2KPL, and 3KPL connections until the new display board is installed. Display Board Removal Procedure Access Board Holder: Open the unit to access the plastic board holder. Release Board Holder: Unlock the two retainer latches of the board holder, then lift and pull out the board holder to access the display board. Disconnect Connectors: Disconnect the 3PL, lKPL, 2KPL, and 3KPL connectors. Remove the display board held by six plastic clips. Display Board Installation Procedure Install Replacement Board: Place the new board in the board holder, ensuring it is securely held by the plastic clips. Reconnect Connectors: Reattach the 3PL, lKPL, 2KPL, and 3KPL connectors. Secure Board Holder: Slide the board holder back into its position and lock it with the two retainer latches. Close Unit and Test: Close up the unit, restore power, and run the KY/LED/DSP LOCAL MODE UTILITY test to verify the correct installation and operation of the new board.

Related models

DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200TBCAG1AAB RTD input terminal board DS200TBCBG1AAA RTD and 4-20ma input terminal board DS200TBQAG1ABB thermocouple terminal plate DS200TBQAG1ABB thermocouple terminal plate DS200TBQBG1ACB I/O terminal board 

DS200TBQBG1ACB I/O terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQEG1BAA LM6000 analog terminal board DS200TBSAG1AAA serial communication terminal module DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCQEG2AED LM 6000 I/O processor DS200TCRAG2ABC relay output board

Related areas

China, mainly using coal. Hydropower is mainly distributed in the source area of south China, which is rich in hydropower. The distribution of nuclear power is not very typical.

Power transmission, including AC power transmission and DC power transmission: For example, the largest power transmission project in China is the West-to-East Power Transmission Project.

Substation; Power distribution; Electricity, electrical machinery and equipment manufacturing.

These are the application fields of our products.

Product features

-Excellent and reliable high-performance EPDM material ensures higher electrical performance; Precise molding of housing ensures superior control of electrical stress;

-Quick and simple installation. The pre-expansion pipe adopts split tubular plastic support pipe, which is convenient to extract and reduces the error of on-site installation time;

-It is suitable for covering the entire cable cross-section range from 50 to 400mm2.