SHINKAWA MODEL VM-5B DUAL ACCELERATION MONITOR

vMODEL VM-5B DUAL ACCELERATION MONITOR 
onitor range Input signal Low cut-off frequency 
*2 High cut-off 
frequency 
*2 Rectification Recorder output 
1 0 to 20m/s2 pk G 0 to 2g pk 1 CA Series 1 10Hz or less 1 100Hz 0 Average value 0 4 to 20mADC 
2 0 to 50m/s2 pk H 0 to 5g pk   2 20Hz 2 200Hz 1 pk-pk 1 1 to 5VDC 
3 0 to 100m/s2 pk J 0 to 10g pk   3 50Hz 3 500Hz 2 rms 
(additional spec./RMS) 2 
Output card 
/IS or /RE 
option 
4 0 to 200m/s2 pk K 0 to 20g pk   4 100Hz 4 1kHz 
5 0 to 20mm/s pk L 0 to 1in/s pk   5 200Hz 5 2kHz   
6 0 to 50mm/s pk M 0 to 2in/s pk   6 500Hz 6 5kHz     
7 0 to 100mm/s pk N 0 to 2g rms 
*1   7 1kHz 7 10kHz     
8 0 to 20m/s2 rms 
*1 P 0 to 5g rms 
*1   8 9.5Hz Seismic filter 
*3 8 20kHz     
A 0 to 50m/s2 rms 
*1 Q 0 to 10g rms 
*1   A 14Hz Seismic filter 
*3       
B 0 to 100m/s2 rms 
*1 R 0 to 20g rms 
*1   B 15Hz Seismic filter 
*3       
C 0 to 200m/s2 rms 
*1 S 0 to 1in/s rms 
*1   C 40Hz(36dB/oct) 
Pipe filter 
*3 
      
D 0 to 20mm/s rms 
*1 T 0 to 2in/s rms 
*1         
E 0 to 50mm/s rms 
*1     D 60Hz(36dB/oct) 
Pipe filter 
*3 

   F 0 to 100mm/s rms 
*1             
Alarm reset 
(DANGER) 
Alarm reset 
(ALERT) 
Alarm reset 
(OK) 
Relay mode 
(DANGER) 
Relay mode 
(ALERT) 
Relay mode 
(OK) 
Alarm delay 
time(DANGER) 
Alarm delay 
time(ALERT) Alarm output type First 
out*4 
0 AUTO-RESET 0 AUTO-RESET 0 AUTO-RESET 0 NORMALLY 
DE-ENERGIZED 0 NORMALLY 
DE-ENERGIZED 0 NORMALLY 
DE-ENERGIZED 
0 3 sec. 0 3 sec. 1 CH1:2 points(DANGER1,ALERT1) 
CH2:2 points(DANGER2,ALERT2) 
0 OFF 
1 SELF-HOLD 1 SELF-HOLD 1 SELF-HOLD 1 1 sec. 1 1 sec. 1 ON 
      1 NORMALLY 
ENERGIZED 1 NORMALLY 
ENERGIZED 1 NORMALLY 
ENERGIZED 
2 6 sec. 2 6 sec. 
2 
CH1:4 points(DANGER1,DANGER2, 
ALERT1,ALERT2) 
CH2:None 
   3 None. 3 None.   
  rms. rectification Isolate output Recorder option 
output 
Input power supply 
requirements*5 
Tropical 
spec. 
Sensitivity  
correction  
When rectification code 2 is 
selected, specify this option code. 
0 4 to 20mADC 2 0 to -10VDC 0 85 to 264VAC  1 TIIS(IEC)  
1 1 to 5VDC 3 0 to 10VDC 1 24VDC  7 NEPSI  
 2 0 to -10VDC 4 0 to -5VDC 2 110VDC     
 3 0 to 10VDC 5 0 to 5VDC       
 4 0 to -5VDC         
 5 0 to 5VDC            
 ALARM SET VALUE DANGER1 :     
ALERT1 :     
DANGER2 :     
ALERT2 :     
Unless specified otherwise, preset to : 
DANGER : 100% of monitor range 
ALERT : 90% of monitor range 
ALARM INDICATOR DANGER : (red LED) 
ALERT : (yellow LED) 
ABNOR.ALARM 
INDICATOR 
OK : (green LED) 
 BYPASS INDICATOR BYPASS : (red LED) 
TRANSUDUCER INPUT CA Series 
Number of input points : 2 points 
SEQUENCE SET 
VALUE 
(to increase alarm set 
value during operation of 
the sequence circuit) 
 :   ×1.0 to 10.0 (×0.1 step) 
Preset to ×1.0 unless specified otherwise. 
CAUTION : Set the alarm set value so that its designated 
multiple is within 110% of the measurement range 
during operation of the sequence circuit. 
If set to more than 110%, alarm may not be output. 
INPUT IMPEDANCE Approx.50k 
EXTERNAL CONTACT 
INPUT 
(FROM REAR PANEL) 
Contact type:Dry contact 
Contact for external reset 
Contact for sequence 
BAR GRAPH METER Recorder output conversion accuracy  ±2.5% of F.S. 
DIGITAL METER Recorder output conversion accuracy  ±1.0% of F.S. 
SUPPRESSION 
FUNCTION SET VALUE 
 :   0.0 to 10.0 % of monitor range (0.1 % step) 
Preset to 2.0 % unless specified otherwise. 
CAUTION : When the measurement value is not more than 
suppression function set value, indication and 
recorder output value shall be as 0 %. 
RECORDER OUTPUT 
CONVERSION 
ACCURACY 
±0.5% of F.S. at calibration frequency at 25°C 
±2.0% of F.S. at calibration frequency at 0 to 65°C 
(the calibration frequency is determined by the cut-off 
frequency range.) 
RECORDER OUTPUT 
(FROM REAR PANEL) 
Voltage or current output proportional to monitor range 
1 to 5VDC (output impedance : 250) 
4 to 20mADC (max.load resistance : 500) 
0 to -10VDC*,0 to 10VDC*,0 to -5VDC*,0 to 5VDC* 
(output impedance : 100) (*option) 
Number of output points : 2 points 
 Standard Specifications 
ALARM SET POINT 4 points(DANGER1,ALERT1,DANGER2,ALERT2) 
ALARM SET RANGE 0 to 110% of monitor range 
ALARM SET 
ACCURACY 
±1.0% of F.S. or less 
 MONITOR OUTPUT 
(FROM FRONT, REAR 
PANEL) 
Input signal is output via a buffer amplifier. 
Signal level : 0.8 to 22VDC 
Output impedance : 100 (load resistance : 50k or more) 
ALARM SET 
REPEATABILITY 
±0.1% of F.S. or less 
 ALARM OUTPUT 5 points (DANGER1,ALERT1,DANGER2,ALERT2,OK) or 
6 points (DANGER1,ALERT1,DANGER2,ALERT2,OK1,OK2) 
TEMPERATIRE RANGE Operating temperature : 0 to 65°C(32 to 149°F) 
Storage temperature : -30 to +85°C(-22 to 185°F) 
Relative himidity : 20 to 95%RH(noncondensing) MEASURED VALUE LCD digital meter with 5 digits (7 segments, with back light) 
LCD bar graph meter (40 segments, with back light) 
 * Measurement value and alarm set value are indicated on 
the digital meter and bar graph meter simultaneously. 
MATERIAL AND FINI