SHINKAWA MODEL VM-5E DUAL CASE

MODEL VM-5E DUAL CASE  
EXPANSION MONITOR
Monitor range Input signal Frequency 
response Polarity 
*1 Operation method Recorder output Alarm reset 
(DANGER) 
Alarm reset 
(ALERT) 
Alarm reset 
(OK) 
1 0 to 25mm 1 VM-21 or VM-11P-20S2 0 DC to 0.5Hz 1 Direct 1 Differential 0 4 to 20mADC 0 AUTO RESET 0 AUTO RESET 0 AUTO RESET 
2 0 to 50mm 2 VM-21 or VM-11P-21S2   2 Reverse 2 Direct 1 1 to 5VDC 1 SELF-HOLD 1 SELF-HOLD 1 SELF-HOLD 
3 0 to 100mm 3 VM-21 or VM-11P-22S2       2 
Output card 
/IS or /RE 
option 
      
4 0 to 1inch 4 VM-21 or VM-11P-23S2           
5 0 to 2inch 5 VM-21 or VM-11P-24S2             
6 0 to 4inch                  

Relay mode 
(DANGER) 
Relay mode 
(ALERT) 
Relay mode 
(OK) 
Alarm delay time 
(DANGER) 
Alarm delay time 
(ALERT) Alarm output type First output*2 
0 NORMARY 
DE-ENERGIZED 0 NORMARY 
DE-ENERGIZED 0 NORMARY 
DE-ENERGIZED 
0 3 sec. 0 3 sec. In case of differential operation 0 OFF 
1 1 sec. 1 1 sec. 1 CH1 : 2 points (DANGER1,ALERT1) 
H,L are OR output 
1 ON 
1 NORMALLY 
ENERGIZED 1 NORMALLY 
ENERGIZED 1 NORMALLY 
ENERGIZED 
2 6 sec. 2 6 sec.   
3 None 3 None 2 CH1 : 4 points (H-DANGER,H-ALERT, 
L-ALERT,L-DANGER) 

          In case of direct operation   
          
3 
CH1 : 2 points (DANGER1,ALERT1) 
H,L are OR output 
CH2 : 2 points (DANGER2,ALERT2) 
H,L are OR output 
          
4 
CH1 : 4 points (H-DANGER,H-ALERT, 
L-ALERT,L-DANGER) 
CH2 : None 

ALARM SET VALUE * H-DANGER1 :     
* H-ALERT1 :     
* L-ALERT1 :     
* L-DANGER1 :     
 H-DANGER2 :     
 H-ALERT2 :     
 L-ALERT2 :     
 L-DANGER2 :     
Only * are set in case of differential operation 
Unless specified otherwise, preset to : 
H-DANGER : 100% of monitor range 
H-ALERT : 90% of monitor range 
L-ALERT : 10% of monitor range 
L-DANGER : 0% of monitor range 
MEASURED VALUE LCD digital meter with 5 digits 
 (7 segments, with back light) 
LCD bar graph meter (40 segments, with back light) 
 * Measurement value and alarm set value are indicated on 
the digital meter and bar graph meter simultaneously. 
ALARM INDICATOR DANGER : (red LED) 
ALERT : (yellow LED) 
ABNOR. ALARM 
INDICATOR 
OK : (green LED) 
 
BYPASS INDICATOR BYPASS : (red LED) 
TRANSDUCER INPUT VM-11P,VM-21P 
Number of input points  :  2 points 
INPUT IMPEDANCE Approx. 250Ω 
EXTERNAL CONTACT 
INPUT 
(FROM REAR PANEL) 
Contact type : Dry contact 
Contact for external reset 
  Standard Specifications 
ALARM SET POINT 8 points (H-DANGER1,H-ALERT1,L-ALERT1,L-DANGER1, 
 H-DANGER2,H-ALERT2,L-ALERT2,L-DANGER2) 
In case of differential operation, 
4 points (H-DANGER,H-ALERT,L-DANGER,L-ALERT) 
BAR GRAPH METER Recorder output conversion acuracy  ± 2.5% of F.S. 
ZERO SHIFT 0 to 100% of monitor range 
DIGITAL METER Recorder output conversion acuracy  ± 1.0% of F.S. 
RECORDER OUTPUT 
CONVERSION 
ACCURACY 
± 0.5% of F.S. at 25°C 
± 2.0% of F.S. at 0 to 65°C 
 
ALARM SET RANGE -10 to +110% of monitor range 
ALARM SET 
ACCURACY 
± 1.0% of F.S. or less 
 RECORDER OUTPUT 
(FROM REAR PANEL) 
Voltage or current output proportional to monitor range 
1 to 5VDC (output impedance : 250Ω) 
4 to 20mADC (max. load resistance : 500Ω) 
0 to -10VDC*,0 to 10VDC*,0 to -5VDC*,0 to 5VDC* 
(output impedance : 100Ω) (*option) 
Number of output points  :  2 points 
When operation method is differential : 1 point 
ALARM SET 
REPEATABILITY 
± 0.1% of F.S. or less 
 
ALARM OUTPUT 5 points (DANGER1,ALERT1,DANGER2,ALERT2,OK) or 
6 points (DANGER1,ALERT1,DANGER2,ALERT2,OK1,OK2) 
In case of differential operation. 
3 points (DANGER,ALERT,OK) or 
4 points (DANGER,ALERT,OK1,OK2) (H,L are OR output) 
(6 points when 4-point alarm is selected for CH1) MONITOR OUTPUT 
(FROM FRONT,REAR 
PANEL) 
Input signal is output via a buffer amplifier. 
Signal level : 1 to 5VDC 
Output impedance : 100Ω (load resistance 50k or more) OTHERS 

TEMPERATURE 
RANGE 
Operating temperature : 0 to 65°C (32 to 149°F) 
Storage temperature : -30 to +85°C (-22 to +185°F) 
Relative humidity : 20 to 95% (noncondensing) 
MATERIAL AND 
FINISH 
Face plate : Aluminum Munsell N-4.0 (equiv.) 
 
MASS Monitor : max.0.7kg 
(including single unit instrument rack : max.2.5kg)