GE VMIVME2540 24-channel intelligent counter/controller

GE VMIVME2540 24-channel intelligent counter/controller

Once programmed by the VMEbus host, theVMIVME-2540 ICC performs these functionsautomatically. The on-board CPU maintains data structuresin shared local memory for buffering measurements andqueueingcontrol commands. Measurement functions arealso supported by a Continuous Measurement Mode inwhich measurements are made repeatedly without host CPUinvolvement. I/O connections are routed throughhigh-density connectors located on the front panel withsupport for differential and single-ended signal levels. Theuser data exchange interface for measurement andgeneration modes complies with ANSI/IEEEStandard754-1985 for 32-bit floating-point arithmetic. Integer modesoperate with two’s complement signed arithmetic and withunsigned arithmetic.

Frequency measurement-1.16 x 10-3 Hz to 2.5 MHzPeriod/pulse width measurement —400 ns to 8.5899 x 106 s (32-bit floating pointPoint), 400 ns to 858 s (32-bit unsigned integer)Square wave/pulse sequence generates-0.0076 Hz to 2.5 MHz.Timer/Periodic VMEbus Interrupter-0.0076 to 000 HzOrthogonal position measurement-sin/cos up to 1 MHz, 32-bit counter,Limit/modulus check16-bit and 32-bit integer period/pulse width measurement, discrete orContinuous; Low data transmission delayProgrammable outputs-up to 24 discrete outputsPulse sequence mode-a sequence of n pulses with programmable duty cycle.Orthogonal position control output-1/4 wave control resolution; 

until1.25 MHz step rate and 32767 steps per command.Integer QPM group acquisition-capture two integer QPM measurements.synchronouslyEvent-triggered timer delay-generates VMEbus interrupts up to 131.1.The number of seconds after the event edge input; Re-trigger24 control/measurement interfaces: 24 clocks, 24 gates and 24 outputs.RS-422 differential interface, supporting single-ended TTL input.Options allow you to configure 4, 8, 16 and 24 interfaces.On-board 15 MHz 68HC000 CPUA32/A24/D32/D16/D8 (EO) VME slave interface, 64 kbyte VMEbusmemory windowData exchange interface: 32-bit ANSI/IEEE standard 754-1985floating-point calculationContinuous measurement modeVMEbus is compatible with ANSI/IEEE 1014-1987 IEC 821 and 297.application programRotating shaft instruments: angular position, speed and accelerationAutomobile industry test: brakes, transmissions and tachometers.roboticsA telescope/observatoryMedical/laboratory instrumentsLinear position measurement: distance, speed and accelerationliftOverhead craneX-Y worktablemachine toolAutomatic storage retrievalProduct overview-VMI VME-2540Intelligent counter/controller (ICC) is a VMEbus slave I/O.The module is designed to provide high-precision numbers.Measurement and function generation abilityThe VMEbus system is simple and consistent.Memory mapping user interface. The following functions areSupported by VMIVME-2540:Measurement functionEvent countfrequency measurementPeriod/pulse width measurementOrthogonal position measurementgeneration functionPulse train/square wave generationTimer/Periodic Interrupt Generationfrequency divisionOrthogonal position control

AboutusThe main products of Xiamen Controllers Automation Technology Co., Ltd. include modules, touch screens, frequency converters and drivers. In addition, they also provide electrical equipment wholesale, computer, software and auxiliary equipment wholesale, other mechanical equipment and electronic products wholesale, electrical installation, professional design services, software development, information system integration services, information technology consulting services and other businesses.

The above information is for reference only. For more information, it is recommended to go to official website or consult relevant staff.

GE  SLN042 IC086SLN042-A  Port small management switch

1,EMERSON: Redundant power supply 1X00, DeltaV control system, switch, FX servo drive

Westinghouse: OVATION system, WDPF system, MAX1000 system spare parts, PAC8000 I/O module, EPRO sensing system MMS,A6 series.

2. Rockwell:

Reliance (Japan Rayon Reliance Electric Limited), servo drive VZ7000, AUTOMAX DCS system 57Cxxx, PSC4000,PSC7000 servo system

Allen-Bradley SLC500/1747/1746 series programmable controller

Allen - Bradley MicroLogix / 1761/1763/1762/1766/1764 series programmable controller,

Allen-Bradley CompactLogix/1769/1768, Series programmable controller

Allen - Bradley Logix 5000/1756/1789/1794/1760/1788, PLC - 5/1771/1785, etc.

Allen-Bradley 2711, 2711P series touch screen,

Medium voltage drive system accessories such as 80026-518-01-R, servo motor MPL

3. Schneider Modicon:

Quantum 140 series processors, control cards, power modules.

Triconex: Redundant fault-tolerant control system, the most modern fault-tolerant controller based on Triple Module Redundancy (TMR) structure, 3623T 3007A 4508 2481 3503E 3625 3721C 4351B 3626X

Foxboro: IA series system, FBM (field input/output module) FCP270, FCP280, FBM231, P0904HA, FBM237, etc.

4, ABB:

AC800M processor system,S800 IO series, S600 S100 IO series

Advant Controller 31, 160, and 250 series

Advant Fieldbus 100 series

ABB Symphony PluS SD + Communication Series,

UNITROL5000, UNITROL6000 excitation system series

Tension sensing PFCL, PFEA, PFTL series

Bailey INFI9, IMDSI02 IMMFP03 IPSYS01

Panel 800 Touch screen PP846 PP836 PP865A

AC 800PEC inverter cabinet controller

ACS5000,ACS6000 medium voltage frequency conversion, etc

5, Siemens (Siemens); 

Siemens MOORE,Siemens Simatic C1, Siemens CNC system,505 system, etc.

6. Motorola :MVME 162,MVME 167,MVME1772,MVME177 and other series.

7, xYCOM: I/O, xVME board and processor.

8, Yaskawa(ochuan) : servo controller, servo motor, servo drive. JANCD-XCP01-1

9. BOSCH Rexroth; : Indramat, l/O module, PLC controller, driver module, etc. DKC02.3-200-7-FW VT3006S34R5 MSK050C-0600-NN-M1-UP1-NSNN VT3002-2X/48F 0608820069

10, Woodward: SPC valve controller, PEAK150 digital controller, 505D controller, etc.

11. General Electric: RX3I IC693CPU, IC695CPU RX7I IC697 698CPU,90-70,VIMC microcomputer system, FANUC drive,Mark IS220 IS215, versMAX programmable controller,vmic VMIVME-, etc

12, United States NI: C M series NI9505 SCXI-1104C PXI-6052E

13. MOOG: motion control servo and D136 programmable module

14. CTI 2500 Series

15. Rolls-Royce: Programmable controller, network communication module

16, Honeywell Honeywell 5701 control system 05701-A-0328 05701-A-0328 CC-PDIL01 900H02-0001, etc