FOXBORO FCP280 FCP270 FEM100 P0926HZ P0923LR P0926JM P0926KH P0926JF

The DIN rail mounted Fieldbus Modules are
packaged as structurally identical plug-in modular
assemblies. To permit mounting in harsh
environments, each module has a rugged, extruded
aluminum exterior, without open vent holes, for
physical protection of the circuits. Heat generated
within the module is conducted from the module via
the aluminum finned cover. This approach to
protection prevents contaminants in the plant
environment from reaching the control components,
greatly extending the life of the equipment. The
operating temperature for a module is rated at either
50°C, 60°C, or 70°C depending on the module and
termination assembly type. The specific Product
Specification Sheet (see “Fieldbus Modules” on
page 14) for each module lists the specific operating
temperature for the module.
The standard DIN rail mounted subsystem has the
following product safety certifications:
 Underwriters Laboratories (UL) listing for both US
(NRTL) and Canadian (UL-C) requirements for
both ordinary and hazardous locations
 CENELEC (DEMKO) certification for use in
potentially explosive atmospheres
 CE approved.
For additional information about certifications, refer to
PSS 31H-2W2 B3.
Light-emitting diodes (LEDs) incorporated into the
front of each module provide visual status indications
of the Fieldbus Module functions.
The small size of these FBMs allows ample room in
an enclosure to terminate field wiring near the FBM.
MODULAR BASEPLATE MODULE MOUNTING
The DIN rail mounted Fieldbus Modules mount on
specially designed Modular Baseplates (Figure 1,
only vertical baseplates shown). The Modular
Baseplates fasten to a structurally supported non
isolated DIN rail for mounting inside or outside an
enclosure. (As an alternative to DIN rail mounting, a
mounting plate can be used for horizontal mounting
of the Modular Baseplate on a 19-inch rack). The
Modular Baseplate provides increased overall system
installation functionality by providing unit increments
of 2, 4 and 8 module positions with various
operational functionality in combination with vertical
and horizontal mounting. The Modular Baseplates
can thus be mounted in small, distributed cabinets or
in a variety of other mounting configurations.
The Modular Baseplates are backwards compatible
with existing DIN I/O subsystems allowing for future
expansion without additional interface hardware and
includes the following:
 Primary and secondary 24 V dc power
connections
Two Module Fieldbus connections (for A/B
Module Fieldbus daisy chain)
 Power/communication connection and field I/O
connection for each FBM
 DIP switch for baseplate identification
 A/B Module Fieldbus and optional time strobe
splitter/terminator connection
 Adding additional baseplates without removing
the system from service (requires redundant
Module Fieldbus).
Any FBM (except FBM232/233) can be removed
from the Modular Baseplate without removing or
disturbing external field device wire terminations or
internal cable terminations or connections.
FCPs, and FCMs require removal of wiring to the
control network.
Shielded twisted-pair cables for Modular Baseplate
interconnections are available in various lengths of
0.25 m (10 in) up to 60 m (198 ft). The maximum
twisted-pair cable length interconnecting all
baseplates is 60 m (198 ft).
Figure 1 shows selected vertical DIN rail mounted
Modular Baseplates. Horizontal DIN rail mounted
Modular Baseplates are available in similar styles as
the vertical mounted baseplates, but equivalents for
each style are not all available. Refer to
PSS 21H-2W6 B4 for additional information on the
remaining DIN rail mounted Modular Baseplates.

Please contact us (kongjiang automation technology), consultation purchase!

 P0912CE NODEBUS B EXTENSION CABLE
 P0913ED DISK DRIVE
 P0914SV INPUT MODULE FBM203 ANALOG ISOLATED 8POINT RTD
 P0914SY I/O MODULE FBM204 4POINT 0-20 IN 4POINT 0-20 OUT
 P0914TD INPUT MODULE FBM207 120AC/125DC,240AC EXCITATION
 P0914TN INPUT MODULE FBM211 DIFFERENTIAL 16POINT 0-20MA
 P0914TN-fbm211 FBM211 DIFFERENTIAL 16 INPUT 0-20 MA
 P0914TR INPUT MODULE FBM217 15-60VDC 120VAC/115VDC 240VAC
 P0914WH INPUT MODULE FBM207B CH ISOLATED 16 DIN 24 VDC
 P0914XA BASEPLATE HORIZONTAL 200SERIES DINRAIL MT FIELDBUS
 P0914XB BACKPLANE 8 SLOT REDUNDANT POWER
 P0914XG I/O MODULE FBM205 4PT 0-20MA IN / 4PT 0-20MA OUT
 P0914YM COMMUNICATION MODULE FCM10E ENET TRUNK TO FIELDBUS
 P0914YM-FCM10E FCM10E FIELDBUS COMMUNICATION MODULE
 P0914ZM IDENTIFICATION MODULE FCMID
 P0915FU TRACKBALL SUN SERIES 51
 P0916AE TERMINATION ASSEMBLY FBM203 3TIER 3WIRE RTD
 P0916AG TERMINAL ASSEMBLY COMPRESSION FBM204
 P0916AG-FBM204 COMPRESSION TERM ASSY, FBM204
 P0916AJ TERMINATION ASSEMBLY FBM205 3TIER COMPRESSION
 P0916AM TERMINATION ASSEMBLY FBM207 2TIER COMPRESSION
 P0916BT TERMINATION ASSEMBLY FBM211 2TIER COMPRESSION
 P0916CP COMMUNICATION MODULE FCM10EF 2KM FIELDBUS
 P0916DD CABLE 5 METERS FBM2XX TYPE 1 TERM
 P0916DE CABLE ASSEMBLY TYPE1 10METER 8POINT 37SUB-25DSUB
 P0916DF CABLE ASSEMBLY TYPE1 15METER 8POINT 37DSUB-25DSUB