KONG -Y
NameDescriptionContent
Location:

Installation Instructions, Fanuc A05B-2256/2255/2518 Pendant Armor®

From: | Author:kongjiang | Time :2025-06-16 | 541 Browse: | 🔊 Click to read aloud ❚❚ ▶ | Share:

 1) Power-down the controller, and disconnect the cable at the pendant 

 2) Remove the Velcro OEM hand strap completely from the pendant 

 3) Place the bumper face up on a clean, dry surface 

 4) Lay the pendant atop the bumper 

 5) Begin by inserting the cable connection into the lower-left corner of the bumper.   Ensure the hand-strap cam and cable connection are fully seated into the bumper.

6) Once the corner is secure, pull the bumper across the bottom of the OEM pendant, then along the sides and over top of the pendant 

 7) Refit the Velcro OEM hand strap to the bumpered pendant (needle-nose pliers will aid with re-installation) 

 8) Note: If your local safety requirements dictate unencumbered or direct access to the E stop button, cut the protective rubber brow as your safety requirements dictate.   Molded cut-lines are embossed around the E-Stop brow.  A utility knife may be used to cut the Santoprene™ 

 9) Reconnect the controller cable 

 10) Power-up the controller 

 11) Installation is complete

Pendant Armor™ Limited Liability Statement:

PENDANT ARMOR (“SELLER”) WARRANTS, TO THE ORIGINAL PURCHASER OR OWNER (“BUYER”) THAT ANY PRODUCT MANUFACTURED AND SOLD BY SELLER WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE AND OPERATION FOR A PERIOD NOT TO EXCEED 90-DAYS.  THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS WHICH HAVE BEEN INSTALLED IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.  IT IS THE BUYER’S RESPONSIBILITY TO INSPECT AND COMPLY WITH ALL STANDARDS RELATING TO THE USE AND OPERATION OF THIS PRODUCT.

THIS LIMITED WARRANTY SHALL BE VOID AND SELLER SHALL NOT BE LIABLE FOR ANY DAMAGES OR HELD RESPONSIBLE FOR THE QUALITY, PERFORMANCE OR SAFETY OF PRODUCTS THAT HAVE BEEN DAMAGED DUE TO ACCIDENT, NEGLIGENCE, MISUSE, OR ABUSE.   SELLER’S SOLE OBLIGATION (AND THE SOLE AND EXCLUSIVE REMEDY OF THE BUYER) WITH RESPECT TO ANY PRODUCT WHICH IS PROVEN TO BE DEFECTIVE, SHALL BE THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT, AT THE SOLE OPTION OF SELLER.  

SELLER SHALL NOT BE LIABLE FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE DEFECTIVE PRODUCT, AND UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES WHETHER BASED ON WARRANTY, CONTRACT OR TORT.

NO CLAIM FOR ANY BREACH OF WARRANTY HEREIN SHALL BE VALID UNLESS DELIVERED TO SELLER IN WRITING WITHIN THIRTY (30) DAYS AFTER DELIVERY OF THE PRODUCT WITH RESPECT TO WHICH THE CLAIM IS MADE.

UNLESS APPLICABLE LAW REQUIRES OTHERWISE, THIS LIMITED WARRANTY IS EXCLUSIVE AND SELLER DISCLAIMS ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.


  • AEROTECH SM Series High-Performance Stepper Motors
  • AEROTECH BLMSC Series Linear Motors
  • AEROTECH Custom Linear Motors
  • AEROTECH BMS Series Brushless, Slotless Rotary Motors
  • AEROTECH BM Series Brushless Rotary Motors
  • AEROTECH BLMX Series Linear Motors
  • AEROTECH BLMH Series Linear Motors
  • AEROTECH BLM Series Linear Motors
  • AEROTECH BLMC Series Linear Motors
  • AEROTECH BLMUC-143    Linear motor forcer with thermistor
  • AEROTECH BLMUC-111    Linear motor forcer with thermistor
  • AEROTECH BLMUC-95  Linear motor forcer with thermistor
  • AEROTECH BLMUC-79 Linear motor forcer with thermistor
  • AEROTECH BLMUC Series Linear Motors
  • AEROTECH Automation1 FLEX Distributed Amplifier Multi-Axis Servo Control System
  • AEROTECH Automation1 FLEX Distributed Amplifier Multi-Axis Servo Control System
  • AEROTECH Automation1 HXA4 6-Axis Hexapod Servo Drive
  • AEROTECH Automation1 iHXA4 6-Axis Hexapod Servo Drive with Motion Controller
  • AEROTECH Modular System Control Console
  • AEROTECH TV Series Transformers
  • AEROTECH TM Series Transformers
  • AEROTECH UFM Noise Filter Module
  • AEROTECH MFM Motor Filter Module
  • AEROTECH MPG Handwheel Pendant
  • AEROTECH Automation1 Multi-Axis Joystick
  • AEROTECH ETM Enhanced Throughput Module
  • AEROTECH Automation1 XL4s High-Speed, Single-Phase Linear Servo Drive
  • AEROTECH Automation1 XL2e Enhanced, Compact Linear Servo Drive
  • AEROTECH Automation1 XL5e Enhanced, Linear Servo Drive
  • AEROTECH Automation1 iXL5e Enhanced Linear Servo Drive with Motion Controller
  • AEROTECH Automation1 GI4 Laser Scan Head Controller
  • AEROTECH Automation1 SI4 Stepper Interface
  • AEROTECH Automation1 XI4 Servo Interface
  • AEROTECH AEROTECH Automation1 iXI4 Servo Interface with Motion Controller
  • AEROTECH Automation1 XC6e Enhanced, High-Power PWM Servo Drive
  • AEROTECH Automation1 iXC6e Enhanced, High-Power PWM Servo Drive with Motion Controller
  • AEROTECH Automation1 XC2 Compact PWM Servo Drive
  • AEROTECH Automation1 XC4 PWM Servo Drive
  • AEROTECH Automation1 GL4 Galvo Laser Scan Head Linear Drive
  • AEROTECH Automation1 XC2e Enhanced, Compact Servo Drive with PWM+
  • AEROTECH Automation1 XC4e Enhanced, PWM Servo Drive
  • AEROTECH Automation1 XR3 Multi-Axis Servo Drive Rack
  • AEROTECH Automation1 iXR3 Multi-Axis Servo Drive Rack with Motion Controller
  • AEROTECH Automation1 iXC2 Compact PWM Servo Drive with Motion Controller
  • AEROTECH Automation1 iXC2e Enhanced, Compact PWM+ Servo Drive with Motion Controller
  • AEROTECH Automation1 iXC4 PWM Servo Drive with Motion Controller
  • AEROTECH Automation1 iXC4e Enhanced, PWM Servo Drive with Motion Controller
  • AEROTECH Automation1 iPC Industrial PC with Motion Controller
  • AEROTECH EPICS & TANGO Drivers for Distributed Control Systems
  • AEROTECH .NET, C, Python & LabVIEW APIs Custom Application Develotpmen
  • AEROTECH Automation1 Industrial Ethernet Support
  • AEROTECH Automation1 iSMC Intelligent, Software-Based Motion Controller
  • AEROTECH Automation1 iXA4 1- 2- or 4-Axis PWM Servo Drive with Motion Controller
  • AEROTECH Automation1 XA4 1- 2- or 4-Axis PWM Servo Drive
  • CTI 2500-ADP2-DISC Discrete Wiring Adapter for Series 500
  • CTI 2500-ADP1 Analog Wiring Adapter for Series 500
  • CTI 2500C-RADP-RS485 Remote Base Controller Adapter for Series 500
  • CTI 2500C-RADP-RBC Profibus RBC Adapter for Series 500
  • CTI 2500C-PADP-120V 120VAC 50W Power Supply for Series 500
  • CTI 2500-RADP RBC Adapter for Series 500
  • CTI 2500-R4500 520/530/DBC Adapter for Series 500 - MATURE
  • CTI 2500-PADP Power Supply Adapter for Series 500
  • CTI 2500-IADP I/O Adapter for Series 500
  • CTI 2500-VP15A-N4-W7 15" Flat-Panel PC with Windows® 7 Embedded
  • CTI 2500S-27-1750 Slice I/O, Ethernet, RS232/485. 900MHz, 2DIO / 4UAI / 2AI
  • CTI 2500S-26-1750 Slice I/O, Ethernet, RS232/485. 900MHz, 8DIO / 2UAI
  • CTI 2500S-23-1750 Slice I/O, Ethernet, RS232/485. 900MHz, 4DI / 4DO / 2UAI / 2AO
  • CTI 2500S-27-1550 Slice I/O, RS232/485. 2DIO / 4UAI / 2AI
  • CTI 2500S-26-1550 Slice I/O, RS232/485. 8DIO / 2UAI
  • CTI 2500S-23-1550 Slice I/O, RS232/485. 4DI / 4DO / 2UAI / 2AO
  • CTI 2500S-27-1050 Slice I/O, Ethernet, 2DIO / 4UAI / 2AI
  • CTI 2500S-26-1050 Slice I/O, Ethernet, 8DIO / 2UAI
  • CTI 2500S-23-1050 Slice I/O, Ethernet, 4DI / 4DO / 2UAI / 2AO
  • CTI 2500C-32F-CJC 32-Pin Field Wiring Connector with Cold Junction Compensation
  • CTI 2500C-32F 32-Pin Field Wiring Connector
  • CTI 2500C-8-TC Eight Thermocouple Inputs
  • CTI 2500C-8-RTD Eight RTD Inputs
  • CTI 2500C-8-RL-FC 8 Form-C Relay Outputs
  • CTI 2500C-8-IDO-24V 8 Isolated 24VDC Outputs
  • CTI 2500C-8-IDO-120V 8 Isolated 120VAC Outputs
  • CTI 2500C-16-DO-24V Sixteen 24VDC Digital Outputs
  • CTI 2500C-16-DO-120V Sixteen 120VAC Digital Outputs
  • CTI 500C-16-IDI-24V Sixteen Isolated 24V AC/DC Digital Inputs
  • CTI 2500C-16-IDI-120V Sixteen Isolated 120V AC/DC Digital Inputs
  • CTI 2500C-16-DIDO-SIM Sixteen Digital Input and Output SImulator
  • CTI 2500C-16-DI-24V Sixteen 24V AC/DC Digital Inputs
  • CTI 2500C-16-DI-120V Sixteen 120V AC/DC Digital Inputs
  • CTI 2500C-RBC-RS485 RS485 Remote Base Controller
  • CTI 2500C-RBC-PRF Profibus Remote Base Controller
  • CTI 2500C-PS-24V-35 35-Watt DC Power Supply
  • CTI 2500C-PS-120V-35 35-Watt AC Power Supply
  • CTI 2500C-R8 Eight-Slot Base
  • CTI 2500C-R4 Four-Slot Base
  • CTI 2500C-R16 Sixteen-Slot Base
  • CTI 2500C-2572-B Fast Ethernet TCP/IP Adapter
  • CTI 2500C-J750 Compact Janus PAC with 3MB Project Memory
  • CTI 2500C-C300 CPU with 512K User Memory
  • CTI 2500C-C200 CPU with 256K User Memory
  • CTI 2500C-C100 CPU with 128K User Memory
  • CTI 2500C-8-AO 8 Analog Outputs
  • CTI 2500C-8-AI 8 Analog Inputs
  • CTI 2559-FCAL Precision Calibration Connector
  • CTI 2559-FPC 2559-FPC 40-pin screw terminal connector
  • CTI 2500-RFC PLC to RF Modem Cable
  • CTI 2500-40F 40-Position Standard Screw-Terminal Connector
  • CTI 2505 Vibration Sensor Interface Module
  • CTI 2554-A 4-Channel Isolated High Speed Counter Module
  • CTI 2553-A 2-Channel Mag Meter Input Module
  • CTI 2502 2-Channel High Speed Counter Input Module
  • CTI 2559-TC 8-Channel Thermocouple Input Module
  • CTI 2556-A 16-Channel Isolated Thermocouple Input Module
  • CTI 2556 16-Channel Isolated Thermocouple Input Module
  • CTI 2551-A 8-Channel Isolated Thermocouple Input Module
  • CTI 2559-RTD 8-Channel RTD Input Module
  • CTI 2557-A 16-Channel RTD Input Module
  • CTI 2557 16-Channel RTD Input Module
  • CTI 2552-A 8-Channel Isolated RTD Input Module
  • CTI 2534 8-Point Form-C Relay Output Module
  • CTI 2532 16-Point Form-A Relay Output Module
  • CTI  2531 32-Point Form-A Relay Output Module
  • CTI  2530 8-Point Form-C Relay Output Module
  • CTI  2562 8-Channel Analog Output Module
  • CTI  2560-A 8-Channel Isolated Analog Output Module
  • CTI  2501 8in/4out Analog Module
  • CTI  2558 8-Channel Analog Input Module
  • CTI  2555-A 16-Channel Analog Input Module
  • CTI  2550-A 8-Channel Isolated Analog Input Module
  • CTI  2599 8/16/32-Point AC Output Module