IS200EGPAG1B General Electric Gate pulse amplifier board

Part Number IS200EGPAG1B Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series EX 2100e Function Module Availability In StockIS200EGPAG1B is an Gate Pulse Amplifier Board manufactured by General Electrics. It is a part of the EX2100e series used in gas turbine excitation system. The primary function is to manage gate commands generated by the ESEL (Excitation System Equipment List) and oversee the gate firing process for up to six SCRs (Silicon Controlled Rectifiers) situated on the Power Bridge. 

Additionally, the EGPA serves as the interface for various important monitoring functions, including current conduction feedback, bridge airflow, and temperature monitoring. Features Gate Control: It plays a pivotal role in controlling the gate firing process of up to six SCRs on the Power Bridge. It takes the gate commands from the ESEL and ensures the precise and timely activation of these critical components. The accurate control of the gate firing is essential for managing power flow and maintaining system stability. Feedback and Monitoring: It acts as an interface for various monitoring functions, including current conduction feedback. 

It allows the system to keep a close eye on the electrical currents in the system, ensuring they remain within safe and desired ranges. Additionally, the EGPA is involved in monitoring bridge airflow and temperature, providing crucial data for thermal management and system safety. Power Supply Management: Receives a nominal 125 V DC power supply from the EPDM (Exciter Power Distribution Module). It houses an onboard DC/DC converter, which converts this input power source into the appropriate levels needed for SCR gating. 

This conversion capability allows the EGPA to function consistently across a wide range of input supply voltage conditions. isual Status Indication: The board is equipped with LEDs that offer visual indications of various system statuses. These LEDs provide information regarding the status of the EGPA power supply, the reception of gate commands from the ESEL, outputs to the SCRs, currents flowing into the bridge, the performance of the line filter, the rotation of the cooling fan, bridge temperature, as well as any alarms or fault conditions. These visual indicators are essential for real-time monitoring, troubleshooting, and maintenance. Sensor Inputs Conduction Current Sensors All three phases of the bridge input are equipped with conduction current sensors. The EGPA serves as an interface between these sensors, which are Hall Effect sensors located on the EXCS (Excitation Control System) boards, and the main control system. Power is supplied to the EXCS, and the EGPA receives signals from the EXCS indicating the status of current flow through each leg of the three-phase bridge input. These status signals are delivered to the EGPA through connectors J9 and J10. 

The EGPA conditions these signals and transmits the bridge's current status to the controller. Bridge Temperature Sensors The temperature of the bridge is monitored using an RTD (Resistance Temperature Detector) sensor input or a temperature switch input. In new exciters, only the RTD input is used, and jumpers on the EGPA disable the temperature switch inputs. In cases where a bridge is being retrofitted with an EX2100 control, the two temperature switch inputs are utilized to interface with temperature switches already mounted on the bridge. In this scenario, the RTD input is left open to disable it. Both the RTD and temperature switch inputs are connected to the EGPA at connector J13. Airflow Sensors (Fan Rotation) To prevent overheating, airflow sensors are used to detect the loss of fan cooling in the bridge. It can accommodate up to four fans, which are connected to it through connector J12. The EGPA accepts either a pulsed or dry-contact, normally open sensor input from the fans. 

The mode of signal detection is configured through berg jumpers JP2-JP4. Line Filter Fuse Failure Sensor A line filter fuse failure is sensed and monitored through connector J14 on the EGPA. This sensor input accepts a single, normally closed, dry contact input. It is designed to detect any failure in the line filter fuse, providing an early indication of potential issues with the power supply.GATE PULSE AMPLIFIER

Related models

0880001-01

104X905BA603

12A0-0103-A3

12HFA51A42H

12HGA11J52

269 PLUS-D/O-100P-125V

369-A200

369B1860G0026

369B1860G0030

369-C100

369-C101

369-HI-0-0-0-0

369-HI-0-M-F-E-0

369-HI-R-M-0-0-0-E

369-HI-R-M-0-E-0

369-HI-R-M-0-P-0-E