IS200JPDFG1A - DC PMD CARD

Part Number IS200JPDFG1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VIe Function Module Availability In StockIS200JPDFG1A is a Power Distribution Board developed by GE. The JPDF board accepts redundant 125 V dc power inputs and distributes power to other system boards. JPDF operates on a floating dc bus centered on Earth rather than a grounded system. This detects system ground faults and has a non-hazardous live 125 V dc rating. IS200JPDFG1A Features Input 125 V dc battery power is connected to a terminal board on the module. Before being connected to the board via the J1 connector, the power is routed through a 125 V dc 30 A circuit breaker and line filter. The alternating current voltage is then routed to three fused non-switched outputs and six fused switched outputs. The alternating current power is routed through the board to the DACA modules, where it is converted to direct current power. DC power is returned to JPDF and combined with the battery power input. JPDF can operate with any combination of one or more active inputs, resulting in a high-reliability 125 V dc power source for the control system. The JPDF module provides full status feedback via a PPDA I/O pack connection. Feedback includes detection of bus magnitude, ground faults, and excessive ac voltage on the dc bus. Each fused branch circuit is checked for the presence of output power. Installation The module is vertically mounted on a metal back base in a PDM cabinet. The JPDF sheet metal must be connected to the system's protective earth (PE). Terminals DCHI and DCLO receive input battery power. Ac power is applied to JAF1 when one or two DACA modules are used, typically from a JPDB module. JZ2 and JZ3 connectors connect DACA modules to JPDF. The system's output circuits are connected as documented. A 50-pin ribbon cable from JPDF connector P1 to the P2 connector on the board containing PPDA is required for a power distribution system with a PPDA power diagnostic I/O pack. Using the P2 connector, this connection can be extended to other core PDM boards. Ground Fault Detection The module supports the use of a dc bus with a high resistance that is centered on ground potential. This configuration detects a ground fault when the positive or negative bus voltages reach ground potential. It includes separate voltage feedback sensing for positive and negative power with respect to ground to support this arrangement. When the feedback is connected to a PPDA I/O pack, the system detects ground faults. The resistance used to center the dc bus on ground determines the sensitivity of ground detection and the ground fault currents that can flow. It has centering resistors chosen by jumper JP1. If centering resistance is provided elsewhere, the JPDF jumper should be left open. JPDF is then designed to introduce the least amount of centering resistance into the system. JP1 should be closed if JPDF is providing the centering function. Only one JPDF module should have a closed JP1 jumper if two are used. Operation Terminals DCHI and DCLO are powered by a dc battery. It then passes through a 30 amp dc circuit breaker and into a filter assembly located beneath the IS200JPDF circuit board. The filtered output is then routed to the JPDF circuit board via a series diode. The JAF1 connector receives alternating current power. The 115/230 V alternating current is routed to two connectors, JZ2 and JZ3, and then out to two DACA modules. The DACA modules convert alternating current to direct current (125 V dc). DC power returns to JPDF via the same JZ2 and JZ3 connectors, where it is combined with battery power if present.Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems

IS200JPDFG1A technical specification

General electric manufacturing company

SeriesMark VI Speedtronic

The part number is 200JPDFG1A.

Functional abbreviations

Function description DC PDM card

PCB coating ordinary coating

IS200JPDFG1A is an ag component as a part of Mark VI system. The system is a part of the long-running Speedtronic series, which was created and developed by General Electric Company for gas/steam turbine management. For more than 30 years, various systems named after Speedtronic have been used for heavy turbine management. Mark VI is one of the last systems released, including Ethernet communication and operating interface based on Windows PC. This is the Mark VI turbine control system series to which 200JPDFG1A PCB belongs. According to its complete GE series name, you may have guessed that this series is specially suitable for the management system and control mode of GE-compatible automatic drive components for gas, wind and steam turbines. In this case, the Mark VI series, which includes the larger Mark VI series of IS200JPDFG1A products, is a considerable improvement over the previous Mark V turbine control system series, because the Mark V series has specific applications only in a more limited range of gas and steam turbine products.

Hardware tips and specifications

IS200JPDFG1A is a part of IS2020JPDF power supply module, which consists of circuit board, metal plate structure with DC circuit breaker, input filter, current limiting resistor and series diode. IS200JPDFG1A can provide connection for two DACA modules if necessary. IS200JPDFG1A board is used to distribute DC power to DC. IS200JPDFG1A uses ribbon cable connection, and carries out system feedback such as DC bus voltage and ground fault detection through PPDA board. IS200JPDFG1A has six toggle switches on a line. Three of them include a warning label that says "Attention, wait 30 seconds after cutting off the power supply". To recharge. IS200JPDFG1A has 18 fuses, and each fuse has its own rated power. It has 14 plug connectors, including a 2-bit plug (10,) a 12-bit plug (2,) and a 9-bit and 5-bit plug. IS200JPDFG1A includes a metal film resistor, a box capacitor, a ceramic capacitor, a TP test point and a transistor. Components are marked with reference marks. For more information about the motherboard and its components, please refer to GE publication GEI-100613. Most of the mentioned resistors, diodes, application specific integrated circuits and various types of capacitor components allocated to normal Mark VI series components of IS200JPDFG1A printed circuit board products only exist as standard components of Mark VI series, which are particularly important for voltage protection and regulation process.

IC697MDL740

IC670PBI001

IC698CHS117C

DS200TCQAG1BHF

IS200AEPCH1ABC

IC697MDL250

IC697MDL250

760-P1-G1-S1-LO-A20-R

SR489-P5-LO-A20-E

IC670CHS001E

IC697MDL653

IS200VTCCH1CBB

VMIVME-4150