IS200TBAIH2C Manufacturer General Electric Country

Part Number IS200TBAIH2C Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockIS200TBAIH2C is an Analog Input/Output Terminal Board manufactured and designed by General Electric as part of the Mark VI Series used in GE Speedtronic Gas Turbine Control Systems.

The Analog Input/Output (TBAI) terminal board supports 10 analog inputs and 2 outputs. The 10 analog inputs accommodate two-wire, three-wire, four-wire, or externally powered transmitters. The analog outputs can be set up for 0-20 mA or 0- 200 mA current. Inputs and outputs have noise suppression circuitry to protect against surge and high-frequency noise. 

TBAI has three DC-37 pin connectors provided on TBAI for connection to the I/O processors. Simplex applications are supported using a single connector (JR1). TMR applications are supported using all three connectors. In TMR applications, the input signals are fanned to the three connectors for the R, S, and T controls. TMR outputs combine the current of the three connected output drivers and determine the total current with a measuring shunt. TBAI then presents the total current signal to the I/O processors for regulation to the commanded setpoint. INSTALLATION: Connect the input and output wires directly to two I/O terminal blocks mounted on the terminal board. Each block is held down with two screws and has 24 terminals accepting up to 12 AWG wires. A shield terminal attachment point is located adjacent to each terminal block. TBAI can accommodate the following analog I/O types: Analog input, two-wire transmitter Analog input, three-wire transmitter Analog input, four-wire transmitter Analog input, externally powered transmitter Analog input, voltage 5 V, 10 V dc Analog output, 0-20 mA Analog output, 0-200 mA OPERATION: TBAI provides a 24 V DC power source for all the transducers. The inputs can be configured as current or voltage inputs using jumpers (J#A and J#B). One of the two analog output circuits is 4-20 mA and the other can be configured as 4-20 mA or 0- 200 mA. The following table displays the analog I/O capacity of TBAI. Each 24 V dc power output is rated to deliver 21 mA continuously and is protected against operation into a short circuit. Transmitters/transducers can be powered by the 24 V dc source in the control system, or can be independently powered. Jumper JO selects the type of current output. Diagnostics monitor each output and a suicide relay in the I/O controller disconnects the corresponding output if a fault cannot be cleared by a command from the processor.TERM. BOARD, ANALOG INPUT (2)

Related models

DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200TBCAG1AAB RTD input terminal board DS200TBCBG1AAA RTD and 4-20ma input terminal board DS200TBQAG1ABB thermocouple terminal plate DS200TBQAG1ABB thermocouple terminal plate DS200TBQBG1ACB I/O terminal board 

DS200TBQBG1ACB I/O terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQEG1BAA LM6000 analog terminal board DS200TBSAG1AAA serial communication terminal module DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCQEG2AED LM 6000 I/O processor DS200TCRAG2ABC relay output board

Related areas

China, mainly using coal. Hydropower is mainly distributed in the source area of south China, which is rich in hydropower. The distribution of nuclear power is not very typical.

Power transmission, including AC power transmission and DC power transmission: For example, the largest power transmission project in China is the West-to-East Power Transmission Project.

Substation; Power distribution; Electricity, electrical machinery and equipment manufacturing.

These are the application fields of our products.

Product features

-Excellent and reliable high-performance EPDM material ensures higher electrical performance; Precise molding of housing ensures superior control of electrical stress;

-Quick and simple installation. The pre-expansion pipe adopts split tubular plastic support pipe, which is convenient to extract and reduces the error of on-site installation time;

-It is suitable for covering the entire cable cross-section range from 50 to 400mm2.