IS200TRLYHIB GE Manufacturing Policy Series Mark VI/VIe Function Module

Part Number IS200TRLYHIB Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockThe IS200TRLYH1B is a Relay Output Terminal Board developed by GE under the Mark VIe series. 

There are 12 plug-in magnetic relays on the Relay Output with Coil Sensing (TRLY1B) terminal board. The first six relay circuits can be set up with jumpers to drive external solenoids or dry, Form-C contact outputs. For field solenoid power, a basic 125 V dc or 115/230 V ac source or an optional 24 V dc source with personal jumper-selectable fuses and onboard suppression can be offered. The next five relays are isolated Form-C contacts that are not powered. An isolated Form-C contact is used on output 12 for specialized uses like ignition transformers. IS200TRLYH1B COMPATIBILITY Simplex and TMR applications are supported by the PDOA/YDOA I/O pack when using the TRLY 1B. 

The terminal board's DC-37 pin connections accept the I/O pack as a plug-in. For simplex systems, connector JA1 is used, while for TMR systems, connectors JR1, JS1, and JT1 are used. IS200TRLYH1B INSTALLATION Wire the two I/O terminal blocks on the terminal board, TRLY1B Terminal Board Wiring, directly with the wires for the 12 relay outputs. Each block has 24 terminals that may accommodate wires up to 12 AWG and is secured with two screws. Each terminal block has a shield terminal strip on the left side that is connected to chassis ground. The solenoid power for outputs 1-6 should be connected to JF1. Power can be daisy-chained to additional TRLYs using JF2. Alternatively, when JF1/JF2 are not in use, power can be connected directly to TB3. Connect output 12 of the special solenoid to connector JG1 to provide electricity. The factory removes jumpers JP1-JP6 and ships them in a plastic bag. If a field solenoid needs electricity, reinstall the proper jumper. Check each loop's energization individually in accordance with best practices, and install the jumpers as necessary. Remove the fuses from isolated contact applications to make sure that the power bus is free of suppression leakage.SIGNAL LVL DETECTOR

Related models

DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200STCAG1ABA Turbine Communication Board (including UCPBG6AFB) DS200TBCAG1AAB RTD input terminal board DS200TBCBG1AAA RTD and 4-20ma input terminal board DS200TBQAG1ABB thermocouple terminal plate DS200TBQAG1ABB thermocouple terminal plate DS200TBQBG1ACB I/O terminal board 

DS200TBQBG1ACB I/O terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQCG1AAA analog input/output terminal board DS200TBQEG1BAA LM6000 analog terminal board DS200TBSAG1AAA serial communication terminal module DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCEAG1BTF emergency overspeed board GE DS200TCQEG2AED LM 6000 I/O processor DS200TCRAG2ABC relay output board

Related areas

China, mainly using coal. Hydropower is mainly distributed in the source area of south China, which is rich in hydropower. The distribution of nuclear power is not very typical.

Power transmission, including AC power transmission and DC power transmission: For example, the largest power transmission project in China is the West-to-East Power Transmission Project.

Substation; Power distribution; Electricity, electrical machinery and equipment manufacturing.

These are the application fields of our products.

Product features

-Excellent and reliable high-performance EPDM material ensures higher electrical performance; Precise molding of housing ensures superior control of electrical stress;

-Quick and simple installation. The pre-expansion pipe adopts split tubular plastic support pipe, which is convenient to extract and reduces the error of on-site installation time;

-It is suitable for covering the entire cable cross-section range from 50 to 400mm2.