IS200TRPAH1A GE Manufacturing Policy Series Mark VI Function Module

IS200TRPAH1A GE Manufacturing Policy Series Mark VI Function Module

Part Number IS200TRPAH1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI Function Module Availability In StockIS200TRPAH1A is an Aeroderivative Turbine Primary Trip Terminal Board manufactured and designed by General Electric as part of the Mark VIe Series used in GE distributed turbine control systems. The Mark VIe / VIeS control system uses the Aeroderivative Turbine Primary Trip TRPA1A and 2A terminal boards in conjunction with PTUR / YTUR I/O packs and TTUR terminal boards. The following are the inputs and outputs: To measure the turbine speed, twelve passive pulse rate devices our in each of the R, S, and T sections ense a toothed wheel. alternatively, six active pulse rate inputs. Two TMR-voted output contacts to the main breaker coil for the trip coil, either 24 V dc (H1A) or 125 V dc (H2A). Four voltage detection circuits for 24-125 V dc voltage for trip string monitoring. One 'Fail-safe' 24-125 V dc device ESTOP input is used to turn off the power to trip relays. INSTALLATION: The I/O terminal blocks TB1 are connected for TTL pulse rate pick-ups, voltage detection, E-Stop, and the breaker relay. TB2 is wired with passive pulse rate pick-up devices. Each block has 24 terminals that may accommodate wires up to #12 AWG and are secured with two screws. Each terminal block is followed by a shield termination strip connected to the chassis ground. Using the following table, the TRPA must be set up for the input connections at the specified speed. Jumpers JP1 and JP2 determine whether the pulse rate pickups from the R section are fanned out to the S and T PTURs or YTURs. OPERATION: The TRPA board is made to be used in two distinct ways. Three cables with DC-37 pin connectors on each end can be used to connect the TTUR terminal board to the TRPA terminal board when it is holding three PTUR or YTUR I/O packs. The TRPA offers four voltage sensors, ESTOP, and two contact-voted trip relay outputs in this mode of operation. The typical set of features listed for that board is offered by TTUR. The TRPA speed inputs should not be connected with this board configuration because they are inactive. Three I/O packs that are directly mounted to the TRPA board can also be utilized with it. This mode of operation enables a single terminal board primary trip solution since the speed inputs to TRPA become active routes into the I/O pack. CONFIGURATION: Jumpers JP1 and JP2 control the fanning of the four passive speed pickups in the R section to the PTURs or YTURs in the S and T sections. To fan the 4 R speed input to the other two TMR sections, place the jumper over the pin pairs.PRIMARY TRIP:AEP

Related models

DS200SHVMG1AFE

IC660ELB912

IS230TVBAH2A

IS215VCMIH2BB IS200VCMIH2BCC

IS210MACCH1AGG

SR489-P5-LO-A20-E

MVR1600-4601

D20 EME 2400-21004

IC697MDL350

8101-HI-TX-02

IC698PSA100

IC698RMX016-ED

IC660BBD025

531X303MCPARG1

DS200FSAAG1ABA

Related areas 

Market application industries include: machine tools, textile machinery, packaging machinery, printing press bending machinery, plastic machinery, rubber and plastic machinery, tobacco machinery, lifting machinery, engineering machinery, logistics and warehousing, elevators, electronic manufacturing, wind power, solar energy, electric power, petrochemicals, building materials, paper making, mining, water guess sliding boring industry, metallurgy, automobiles, railways, tracks, buildings.

product information 

Product category: functional module 

Brand: GE

Special purpose: none 

Processing customization: No. 

Specification: 2.66mm 

Output frequency: 1.255Hz 

Installation method: control room installation