KONG -Y
NameDescriptionContent
Location:

Basler Electric DECS-200 Digital Excitation Control System

From:Basler Electric | Author:kongjiang | Time :2026-07-20 | 544 Browse: | 🔊 Click to read aloud ❚❚ ▶ | Share:

Basler Electric DECS-200 Digital Excitation Control System

This instruction manual provides information about the operation and installation of the DECS-200 Digital

Excitation Control System. To accomplish this, the following information is provided:

• General Information and Specifications

• Controls and Indicators

• Functional Description

• Installation

• Maintenance

INTRODUCTION

The Basler Digital Excitation Control System (DECS-200) is a microprocessor-based control device

intended for generator power management. Programmability of system parameters and regulation

settings enables the DECS-200 to be used in a wide range of applications and provides greater flexibility

in excitation system optimization. The DECS-200 can accommodate generator exciter field requirements

up to 15 Adc continuously in 32. 63. or 125 Vdc applications with one model.

FEATURES

DECS-200 units have the following features and capabilities.

Functions

• Four control modes

o Automatic voltage regulation (AVR)

o Manual or field current regulation (FCR)

o Power factor (PF)

o Reactive power (var)

• Soft start buildup with an adjustable ramp in AVR and FCR control modes

• One adjustment range or pre-position setpoint for each control mode

• Overexcitation limiting (OEL) and underexcitation limiting (UEL) in AVR, var and PF control modes

• Twenty stability selections

• Underfrequency compensation or volts per hertz ratio limiter

• Autotracking between operating modes and between DECS-200 units (optional)

• Automatic transfer to a backup DECS-200 unit (optional)

• Eight generator protection features

o Field overvoltage

o Field overcurrent

o Generator overvoltage

o Generator undervoltage

o Watchdog timer

o Loss of sensing

o Exciter diode monitor (EDM)

o Loss of field

• Generator paralleling with reactive droop compensation and reactive differential compensation

• Data logging and event recording

Inputs and Outputs

• Single-phase rms bus voltage sensing

• Single-phase or three-phase rms generator voltage sensing

• Single-phase generator current sensing (1 or 5 amperes, nominal)

• Analog inputs (±10 Vdc and 4 to 20 mAdc) provide proportional, remote control of the setpoint

• Eleven PLC-compatible contact sensing inputs for system interface

• Separate ac and dc power inputs accommodate redundant operating power sources

• Pulse-width modulated output power stage rated at a maximum of 15 amperes, continuous

• Five output relays for system control or annunciation

o Three programmable output relays

o Two fixed-function output relays

HMI Interface

• Front panel HMI includes pushbutton controls, LED indicators and a backlit, liquid crystal display

(LCD)

• BESTCOMS™ Windows® based software provides easy, fast and accurate setup and control

Three communication ports

o Front RS-232 port for communication with a PC using BESTCOMS software

o Right-side panel RS-232 port for dedicated communication with a redundant DECS-200

o RS-485 communication port for communication with a remote terminal

• Modbus protocol for the RS-485 port allows communication at distances of up to 1.200 meters

(3.937 feet)

Introduction

In the typical application shown in Figure 1-1. the DECS-200 controls the exciter field of a synchronous

generator. Front panel controls, indicators, and serial communication ports using PC software make the

system easy to operate locally or from remote locations. DECS-200 operation, settings, and safety setup

procedures in this manual should be studied before implementing your application. For detailed

application assistance, contact Basler Electric or your local sales representative.

Operating Power

Operating power for the pulse-width modulated (PWM) excitation output is typically obtained from the

generator output through a power transformer. Alternately, operating power can be supplied from a

permanent magnet generator (PMG).

During DECS-200 power-up, an optional ICRM (Inrush Current Reduction Module) prevents damage to

the DECS-200 by limiting inrush current to a safe level. For more information, refer to Section 4.

Installation.

Control Power

If power supply option C (120/125 Vac/Vdc) is selected, a redundant power source can be used with the

DECS-200. (See Figure 1-1.) In this configuration, if one of the two sources fails, the other source will

continue to supply DECS-200 operating power. If power supply option L (24/48 Vdc) is selected, no

redundant power source is available.

Sensing

The DECS-200 senses generator voltage and current through voltage and current transformers. Field

voltage and field current values are sensed internally.

Excitation Limiters

Integrated overexcitation and underexcitation limiters (OEL and UEL) are available for both on-line and

off-line protection.

External Tracking and Transfer Between DECS-200 Units (Optional)

For critical applications, a second DECS-200 can provide backup excitation control. The DECS-200

allows for excitation system redundancy by providing external tracking and transfer provisions between

DECS-200 units. The secondary DECS-200 operating modes can be programmed to track the primary

DECS-200 operating mode. Proper, redundant excitation system design allows for removal of the failed

system. Periodic testing of the backup system must be performed to ensure that it is operational and can

  • Beckhoff FC9002 | Ethernet card, 2 channels, PCI
  • Beckhoff FC7502 | Sercos II master card, 2 channels, PCI™
  • Beckhoff FC7501 | Sercos II master card, 1 channel, PCI™
  • Beckhoff FC5322 | CAN FD card, 2 channels, PCIe® x1
  • Beckhoff FC5321 | CAN FD card, 1 channel, PCIe® x1
  • Beckhoff FC5202 | DeviceNet®, master/slave card, 2 channels, PCI™
  • Beckhoff FC5201 | DeviceNet® master/slave card, 1 channel, PCI™
  • Beckhoff FC5122 | CANopen master/slave card, 2 channels, PCIe® x1
  • Beckhoff FC5121 | CANopen master/slave card, 1 channel, PCIe® x1
  • Beckhoff FC5102 | CANopen master/slave card, 2 channels, PCI™
  • Beckhoff FC5101 | CANopen master/slave card, 1 channel, PCI™
  • Beckhoff FC3122 | PROFIBUS master/slave card, 2 channels, PCIe® x1
  • Beckhoff FC3121 | PROFIBUS master/slave card, 1 channel, PCIe® x1
  • Beckhoff FC3102 | PROFIBUS master/slave card, 2 channels, PCI™
  • Beckhoff FC3101 | PROFIBUS master/slave card, 1 channel, PCI™
  • Beckhoff FC1428 | EtherCAT G master card, 8 channels, PCIe® x4
  • Beckhoff FC1121 | EtherCAT slave card, 1 channel, PCIe® x1
  • Beckhoff FC1100 | EtherCAT slave card, 1 channel, PCI™
  • Beckhoff FC1028 | EtherCAT master card, 16 channels, PCIe® x4
  • Beckhoff FC9062 | Gigabit Ethernet PCIe® module, 2-channel
  • Beckhoff C9900-R266 | NOVRAM PCIe® module
  • Beckhoff FC3161 | PROFIBUS master/slave PCIe® module, 1 channel
  • Beckhoff C9900-E301 | RS232 PCIe® module, 2 channels
  • Beckhoff C9900-E277 | USB 3.0 PCIe® module, 2 channels
  • Beckhoff C9900-E276 | PCIe® module for CP-Link 4 – The Two Cable Display Link
  • Beckhoff C9900-E271 | USB Extender 2.0 Tx PCIe® module, 1 channel
  • Beckhoff CU8803-000x | Transmitter box for CP-Link 4 – The One Cable Display Link
  • Beckhoff CU8802-000x | Transmitter box for CP-Link-4 – The Two Cable Display Link
  • Beckhoff CU8851 | USB extension, USB Extended 2.0 receiver box
  • Beckhoff CU8801-0000 | USB extension, USB Extended 2.0 transmitter box
  • Beckhoff CU8880-0010 | Ethernet controller with USB input
  • Beckhoff CU8871 | USB CFast slot
  • Beckhoff CU8870 | USB CompactFlash® slot
  • Beckhoff CU8815 | DVI splitter
  • Beckhoff CU8810-0010 | DVI splitter with USB extender
  • Beckhoff CU8006 | 4-port USB 3.0 hub
  • Beckhoff C9900-U332-0010 | Battery pack
  • Beckhoff C9900-U330 | Battery pack
  • Beckhoff C6670-0010 | Control cabinet industrial server
  • Beckhoff C6670-0020 | Control cabinet industrial server
  • Beckhoff C6240-0070 | Control cabinet Industrial PC
  • Beckhoff C6240-0080 | Control cabinet Industrial PC
  • Beckhoff C6675-0060 | Control cabinet Industrial PC
  • Beckhoff C6675-0070 | Control cabinet Industrial PC
  • Beckhoff C6650-0050 | Control cabinet Industrial PC
  • Beckhoff C6650-0070 | Control cabinet Industrial PC
  • Beckhoff C6640-0060 | Control cabinet Industrial PC
  • Beckhoff C6640-0070 | Control cabinet Industrial PC
  • Beckhoff C5210-0030 | 19-inch slide-in Industrial PC
  • Beckhoff C5210-0040 | 19-inch slide-in Industrial PC
  • Beckhoff C5210-0050 | 19-inch slide-in Industrial PC
  • Beckhoff C5240-0010 | 19-inch slide-in Industrial PC
  • Beckhoff C5240-0030 | 19-inch slide-in Industrial PC
  • Beckhoff C7015-0020 | Ultra-compact Industrial PC in IP65
  • Beckhoff C7015-0020 | Ultra-compact Industrial PC in IP65
  • Beckhoff C7015-0030 | Ultra-compact Industrial PC in IP65
  • Beckhoff C6525-0060 | Fanless built-in Industrial PC
  • Beckhoff C6525-0070 | Fanless built-in Industrial PC
  • Beckhoff C6525-0080 | Fanless built-in Industrial PC
  • Beckhoff C6515-0060 | Fanless built-in Industrial PC
  • Beckhoff C6515-0070 | Fanless built-in Industrial PC
  • Beckhoff C6515-0080 | Fanless built-in Industrial PC
  • Beckhoff C6043-0090 | Ultra-compact Industrial PC with NVIDIA® GPU
  • Beckhoff C6040-0090 | Ultra-compact Industrial PC
  • Beckhoff C6032-0060 | Ultra-compact Industrial PC
  • Beckhoff C6032-0070 | Ultra-compact Industrial PC
  • Beckhoff C6032-0080 | Ultra-compact Industrial PC
  • Beckhoff C6030-0070 | Ultra-compact Industrial PC
  • Beckhoff C6030-0080 | Ultra-compact Industrial PC
  • Beckhoff C6027-0000 | Fanless ultra-compact Industrial PC
  • Beckhoff C6027-0010 | Fanless ultra-compact Industrial PC
  • Beckhoff C6025-0000 | Fanless ultra-compact Industrial PC
  • Beckhoff C6025-0010 | Fanless ultra-compact Industrial PC
  • Beckhoff C6025-0020 | Fanless ultra-compact Industrial PC
  • Beckhoff C6930-0060 | Control cabinet Industrial PC
  • Beckhoff C6930-0070 | Control cabinet Industrial PC
  • Beckhoff C6930-0080 | Control cabinet Industrial PC
  • Beckhoff C6925-0030 | Fanless control cabinet Industrial PC
  • Beckhoff C6925-0040 | Fanless control cabinet Industrial PC
  • Beckhoff C6915-0010 | Fanless control cabinet Industrial PC
  • Beckhoff C6915-0020 | Fanless control cabinet Industrial PC
  • Beckhoff C6905-0010 | Economy control cabinet Industrial PC
  • Beckhoff C6905-0020 Economy control cabinet Industrial PC
  • Beckhoff C6905-0030 Economy control cabinet Industrial PC
  • Eaton SPN6084LEAXX2F Power Defense SB
  • Eaton MPNC4N3LEAXXSW Magnum low voltage power circuit breaker
  • EatonSP N8403YEAXX2H Power Defense SB
  • Eaton MPS8604WEAXX2C Magnum low voltage power circuit breaker
  • Eaton MPS8404WEAXXSW Magnum low voltage power circuit breaker
  • Eaton MPN6504LEAXX3A
  • Eaton MPSC323VEAXX2A Magnum low voltage power circuit breaker
  • Eaton SPS6304WEAXX2F Power Defense SB
  • Eaton MPN6504LEAXX2H Magnum low voltage power circuit breaker
  • Eaton MPSC504HEAXX2H Magnum low voltage power circuit breake
  • Eaton SPN85N3LEAXX2F Power Defense SB
  • Eaton SPN6403CEAXX2F Power Defense SB
  • Eaton MPSC5N4MEAXX3A Power Defense SB
  • Eaton SPSC124WEAXX2A Power Defense SB
  • Eaton SPS85A4WEAXX2H Power Defense SB
  • Eaton SPSC5N4MEAXX2A Power Defense SB
  • Eaton MPN8403VEAXX2H Magnum low voltage power circuit breaker
  • NZMB2-4-A200 MCCB NZM, NZM2 TM and Elec
  • Eaton NZMN1-A63 Series NZM complete molded case circuit breaker
  • Eaton NZMB1-S26-CNA Series NZM complete molded case circuit breaker
  • Eaton NZMH2-A25-NA Series NZM complete molded case circuit breaker
  • NZMH2-A200-BT-NA Eaton Series NZM complete molded case circuit breaker
  • NZMN4-VEF1200-NA Eaton Series NZM complete molded case circuit breaker
  • NZMH2-AF250-NA MCCB NZM, NZM2 TM and Elec
  • NZMB1-AF60-NA Eaton Series NZM complete molded case circuit breaker
  • NZMN1-A50 Eaton Series NZM complete molded case circuit breaker
  • NZMH2-A80-NA Eaton Series NZM complete molded case circuit breaker
  • Eaton Cutler-Hammer HFD3030 6639C86G87 3 Pole 30A 600V Circuit Breaker
  • Moeller XV-230-57CNN-1-13-1 HMI PLC Panel Touchscreen 5.7"
  • EATON CEAG CU CG-S , 40071360300 Control Unit
  • EATON SDN90186 MOTOR CONTROL CENTER
  • EATON HMCP150U4 CIRCUIT BREAKER
  • Eaton 7801C57 Digitrip Optimizer Hand Held Programmer
  • Eaton HMCP400R5 Circuit Breaker
  • EATON MP-3000 SAFETY RELAY 66D2032GX1
  • EATON PGGLOBL1701DPRO 1785T Touch Panel
  • Eaton, Moeller, Easy MFD-CP8-NT
  • Eaton WL-35717F Vacuum Interrupter
  • EATON VICKERS EEA-PAM-535-A-32 AMPLIFIER CARD
  • EATON FP5000-00 / FP5200-00 66D2041G11 FEEDER PROTECTION RELAY
  • Eaton IQ-504 120VAC Modular Overload Relay
  • Beckhoff CX5620-0225    CPU module
  • Beckhoff CX5620-0220    CPU module
  • Beckhoff CX5620-0215    CPU module, Beckhoff RT Linux®