EMERSON Part Number D301150X412 FloBoss™ S600+ Flow Computer Instruction Manual

FloBoss S600+ Flow Computer

The FloBoss S600+ Flow Computer is a panel-mounted (for indooruse)

flow computer designed specifically to measure hydrocarbon

liquid and gas where versatility and accuracy matter. The standard

features of the S600+ make it ideal for fiscal measurement, custody

transfer, batch loading, and meter proving applications. The S600+

allows you to configure multi-stream, multi-station applications,

enabling you to simultaneously meter liquids and gasses.

The S600+ is designed for use either as a stand-alone flow computer or

as a system component. The intelligent I/O modules fit both gas and

liquid applications and typically support two dual-pulsed streams and a

header. Adding I/O modules (up to a maximum of three) allows you to configure up to six dual-pulsed streams or up to 10 single-pulsed streams and two headers. The S600+ supports orifice, ultrasonic, turbine, positive displacement, Coriolis, Annubar, and V-Cone® flow meter types and master meter, small volume compact, and pipe (both bi-directional and uni-directional) proving methods.

The S600+ offers a variety of communication interfaces:

 Two LAN ports (on the enhanced CPU module) for Ethernet 10Base-T or 100Base-T full-duplex connectivity (using either Modbus TCP or Modbus over Ethernet protocols).

Note: The Ethernet module (P190), which provided an additional Ethernet port for previous versions of the S600, is not compatible with the S600+.

 HART® communication using up to two 12-channel HART modules, each of which supports point-to-point and multi-drop architectures for up to 50 transmitters.

Note: The FloBoss S600+ is fully compatible with HART 5 devices, and HART 7 devices are backwards compatible with HART 5 devices.

 An embedded webserver allows remote access to the flow computer. Security is provided using user name and password protection with a detailed event log for audit purposes (supports Microsoft® Edge™ or Windows® Internet Explorer® version 5 or greater [version 9 or greater must use compatibility mode]).

 Two configurable RS-232 serial ports.

 Three RS-422/RS-485 serial ports (supporting up to 57,600 bps baud) and up to four RS-485 2-wire serial ports (supporting up to 57,600 baud rate) for connection to intelligent meters, Modbus SCADA data networks, DCS supervisory systems, and so on.

 One dedicated configuration port (located on the bottom of front display panel) for connection to the Config 600 configuration software.

 Additional communications interfaces include:

• Serial Q.Sonic®

• Serial printer

• Serial or Modbus TCP Daniel chromatograph via Modbus

• Serial peer-to-peer

• Modbus EFM protocol, Modbus RTU, Modbus ASCII, Modbus over Ethernet, and Modbus TCP

 Miscellaneous interfaces which can operate via serial or Modbus TCP:

 Daniel liquid ultrasonic

 Daniel gas ultrasonic

 Sick ultrasonic  Daniel chromatograph

Note: All ports can connect to DCS systems, ultrasonic meters, Coriolis meters, and so on.

The S600+ uses distributed processing to achieve maximum performance. The CPU module incorporates a hardware floating point processor. Each additional module also has local processing to convert inputs and output from engineering units to field values and vice-versa, as well as running background tests and PID loops.

The firmware uses 64-bit (double) precision floating point numbers for the highest accuracy when performing all metering calculations. Cumulative totals are stored in three separate memory locations (Tri-reg format) for maximum integrity. The user language LogiCalc™ also allows you to perform logical control and double-precision mathematical functions on the database objects.

Front Display Panel

The S600+’s front panel interface enables you to manage an existing configuration or create a configuration using the PC-based Config 600 configuration software.

A communications port on the bottom of the panel provides a way to directly connect to a PC. The front panel interface consists of a backlit LCD display, a 29-button keypad, and an alarm status LED (see Figure 1-4).

Config600 Configuration Software

Using Config 600, you can both send (upload) new or modified configurations to the S600+ and receive (download) existing

configurations from the S600+. You can also define the following functions:

 Stream and station totalisation.

 Batch totalisation and correction.

 Three-term PID control.

 Flow balancing.

 Flow scheduling.

 Automatic proving sequence.

 K-factor or meter factor linearisation.

 Valve monitor/control.

 Sampler control.

 Station densitometer.

 Station gas chromatograph.

 Forward, reverse, and premium error totals.

 Comprehensive maintenance mode.

 Reporting.

 Modbus.

 Modify display matrix.

Config600 is a suite of software editors that enables you to monitor, configure, and calibrate the S600+. The software comes in three versions – Config600 Lite, Config600 Lite Plus, and Config600 Pro – with Config600 Pro being the most powerful version.

Note: The S600+ does not operate until you send a configuration to it from the host PC.

IPL600

Remote Automation Solutions provides a separate utility program called “Interactive Program Loader 600” (or “IPL600”).